Zennio ZoningBOX 6 Page 40 User Manual Download

Page: 40 / 44

ZoningBOX 6/ ZoningBOX 4

http://www.zennio.com

Technical Support:

http://support.zennio.com

ANNEX I. INTERACTION BETWEEN MODULES

[Unit x] On/Off HVAC Unit (Status)

[Unit x] On/Off HVAC Unit

[Unit x] Modo

[Unit x] Temperature Restriction

[Unit x] Min. Limit Temperature

[Unit x] Max. Limit Temperature

[Unit x] Fan: Speed

[Group n] [Zi] Enable/Disable Zone

[Group n] [Zi] Setpoint Temperature

[Group n] [Zi] Reference Temperature

[Group n] [Zi] Control Signal from Thermostat

[Unit x] Mode (status)

[Unit x] Global Temperature Setpoint

[Unit x] Fan: Speed (status)

[Unit x] Open/Close Bypass

[Group n] [Gi] [Control] Grille Control

[Group n] [Gi] [Control] Grille Status

[Unit x] Return Temperature

[Group n] [Gi] [Actuator] Grille Position

[Group n] [Gi] [Actuator] Grille Status

Controller

from Zone

“y”

(Thermostat)

Zoning Module (ZoningBOX)

External sensor

HVAC Unit
Gateway

Actuator of the
Bypass Valve

Grille
Control Module
(ZoningBOX)

Summary of Contents for ZoningBOX 6













































Search results

Summary of Contents for ZoningBOX 6

Reviews:

Related manuals for ZoningBOX 6

Brands by name

Popular brands

Zennio ZoningBOX 6, User Manual

Search results

Summary of Contents for ZoningBOX 6

Reviews:

Related manuals for ZoningBOX 6

Brands by name

Popular brands