Zelmer ZVC722 Series, User Manual

Page: 57 / 60

57
23 Turbo brush (type 829.0 ST)
24 SAFBAG dust bag holder
25 Water filter module:
A Filtration unit
B Partition
26 Container
Preparing the vacuum cleaner for
operation
1 Insert the end of the suction hose to the vacuum cleaner
opening so that the hose interlock is in the protrusion of the
opening. A characteristic click indicates that the hose has
been properly installed.
2 Connect the other end of the hose (handle) with the
telescopic suction tube.
3 Hold the ring on the pipe and set chosen length putting it
in or out.
4
Assemble the appropriate nozzle or brush to the other
end of the suction tube.
5 You may assemble a basket for picking up small objects
in the combination brush with small item separator. In order
to do so remove the basket cover and insert the basket.
6 To clean hard surfaces – wooden floors, plastic floors,
ceramic tiles etc. pull out the brush by pressing the switch on
the nozzle according to the figure .
7 The vacuum cleaner is equipped with an accessory
compartment. The compartment is located in the front lid of
the appliance. To open/close the compartment lift/close the
lid and take out/ put away the desired nozzle.
8 The vacuum cleaner may be stored in a horizontal
position; in order to this, place the fastening hook of the
combination nozzle/brush into its fastening. The hose may
be left attached to the vacuum cleaner, but it is important to
pay attention not to leave it heavily bent during storage.
9 Grab the plug (3) and pull the cord out of the vacuum
cleaner.
●
Plug in the appliance.
Before operation, make sure that all filters as
well as the appropriate module are installed in
the appliance.
10 Switch on the vacuum cleaner by pressing the “on/off”
button (1) .
Vacuum cleaner functions
TRADITIONAL CLEANING WITH SAFBAG
DUST BAG
1 Press the “PRESS” button and remove the tank lid.
2
Put the SAFBAG holder (24) into the container. Make
sure the holder is inserted correctly in the container guide
slots and the safety lock is engaged. Unfold the bag in the
container.
B
C
The water filter module/the dry filtration
module with the SAFBAG dust bag may only be
removed and inserted when the end of the hose
is removed from the vacuum cleaner opening.
Do not put SAFBAG holder into a wet container.
Thoroughly dry a wet container. SAFBAG dust
bag must not get wet.
3 Cover the container with the filtration unit.
If the SAFBAG holder is not attached properly,
the safety lock will prevent covering the
container with the filtration unit.
●
Prepare the vacuum cleaner for operation according
to section B.
4
The vacuum cleaner starts up with default setting of the
highest power range. One diode will light on the power level
indicator (6) . Set the desired power value (this function is
only available in vacuum cleaners type 829.0) by pressing
the power adjustment buttons , (5) .
SAFBAG dust bag disassembly/assembly
1 Remove the filtration unit from the container and pull out
the SAFBAG holder (24) .
The water filter module/the dry filtration
module with the SAFBAG dust bag may only be
removed and inserted when the end of the hose
is removed from the vacuum cleaner opening.
2
Lift the SAFBAG tab and slide the dust bag from the
holder guide.
3 Slide the new SAFBAG tab all the way into the holder
guide as directed by the arrow printed on the bag until tab
locks in the guide.
4
Put the SAFBAG holder (24) in the container and cover
with the filtration unit in accordance with paragraphs C2
and C3 .
If the SAFBAG dust bag is not properly attached
to the holder, the safety lock will prevent
covering the container with the filtration unit.
VACUUM CLEANING WITH THE USE OF THE
WATER FILTER MODULE
1 Press the “PRESS” button and remove the tank lid.
2 Insert the partition in the container. Make sure the
partition is inserted correctly in the container guide slots and
the safety lock is engaged.
3
Fill the container with 1,2 liter of water. The water level
should be in the range marked on the tank wall.
Do not operate the appliance with an empty
container while vacuum cleaning with the use
of the water filter module.
4 Cover the container with the filtration unit.
D
E