Zelmer ZVC722 Series, User Manual

Page: 58 / 60

58
If the partition is not inserted properly, the
safety lock will prevent covering the container
with the filtration unit.
●
Prepare the vacuum cleaner for operation according
to section B.
The vacuum cleaner starts up with default setting of the
highest power range. One diode will light on the power level
indicator (6) . Set the desired power value (this function is
only available in vacuum cleaners type 829.0) by pressing
the power adjustment buttons , (5) .
Do not operate the appliance for too long
without replacing the water in the container.
In case of long-term or very intensive
vacuuming of large amounts of dirt, the water
in the tank which constitutes the first filtration
level may in whole or in a considerable part be
absorbed by the dirt. In such a case, exchange
the water and continue vacuuming.
Avoid vacuuming surfaces covered with substances which
may favor an excessive foaming of the water inside the
tank. If you notice that the water is heavily foamed, add
a foam neutralizer recommended by the manufacturer of the
appliance e.g. “G 478 Buz
®
Defoam” in the amount indicated
on the packaging. It can be purchased in stores which offer
ZELMER products or by mail order.
Vacuuming with the amount of water in the tank
which exceeds the marked, permissible level
may cause the water to spill to the outside of the
appliance. If this situation repeats often, it may
lead to a fast clogging of the outlet EPA E10 filter.
The vacuum cleaner is equipped with a float
which will automatically block the suction if the
foam filter II (10) is heavily dirty or the liquid
exceeds the maximum level. In such a case
switch off the vacuum cleaner by pressing the
on/off button (1), unplug the appliance, clean
the filter and empty the container.
PICKING UP WATER
If you want to use the vacuum cleaner to vacuum liquid, the
vacuum cleaner should be prepared as in the case of vacuum
cleaning with the use of the water filter module except that:
●
The container should be empty (without water).
●
You should use the nozzle for picking up water (20) .
Do not operate the vacuum cleaner with a full
container! Do not vacuum large amounts of
liquid at a time (e.g. with the hose immersed
into water).
If the water exceeds the maximum level during vacuuming,
the float will automatically block the suction. The maximum
capacity of the container is about 4,0 l. In such a case proceed
in the manner described above in the part concerning the
blocking of suction caused by a dirty foam filter.
End of operation cleaning and maintenance
●
Switch off the vacuum cleaner by pressing the on/off
button (1) and unplug the appliance.
●
Wind the cord by pressing the cord rewind button (4) .
While doing this hold the cord to make sure it is not
tangled and the plug does not hit the vacuum cleaner
housing.
●
Press the interlock on the hose end and remove the
hose from the opening.
●
Disconnect the telescopic tube from the hose and the
nozzle or brush.
●
In case of vacuuming or picking up water with the use
of the water filter module, remove the dirty water from
the tank.
●
It is recommended to wash the container, filters
(disassembly below) and partition thoroughly after each
use – changing water several times.
If you do not clean the above-mentioned parts
or clean them insufficiently it may lead to the
loss of the filtration capabilities of the inserts
and foam and cause the formation of bacteria
and mites.
Dry all the cleaned parts thoroughly before
reassembly.
Filter disassembly
FOAM FILTER I
1 Open the lid of the filter unit – press the handle and lift
the lid.
2 Take out the filter, wash it under running water, dry and
reinsert.
●
Close the filter unit lid by pressing it until you hear
a characteristic click.
FOAM FILTER II
It is recommended to wear rubber protective gloves while
dismantling the filter.
1 Grab the foam filter with your fingers and remove it from
the filter unit body.
2 Wash under running water, dry and reinsert.
Do not hand wash the filter foam, do not wring
it, do not wash it in washing machines. Avoid
crumpling, stretching and deforming. After
cleaning dry the foam in room temperature.
Never dry the foam on heaters, stoves, etc.
MOTOR FILTER
A filtration fabric is inserted in the motor cooling cycle which
is to catch the coal dust which arises due to the natural wear
and tear of the brushes and the commutator in the motor.
1 Remove the tank from the vacuum cleaner.
F
G
H