59
The manufacturer does not accept any liability for any damages
resulting from unintended use or inappropriate handling.
The manufacturer reserves his rights for modifying the product any
time in order to adjust it to law regulations, norms, directives, or due
to construction, trade aesthetic or other reasons, without notifying it
in advance.
2
Place the vacuum cleaner with the “wheels upwards” so
that the upper sloping surface and the handle are rested on
the floor. Insert a flat, narrow tool e.g. a screwdriver into the
special slot of the filter lid; pry the fastening with an upward
hand movement (lever principle) which will release the lid
wwlatch while being bent.
3
If the motor filter
(9)
is dirty, it is possible to rinse the
filter
(9)
under running water. Remember to dry the above
mentioned filter before reassembly.
4
Insert the new/rinsed motor filter
(9)
, make sure that the
filter edges do not remain outside the outline of the section.
Snap the filter lid shut by first inserting the lower fastening
and then pressing the fastening so that the upper fastening
clicks into place at the edge of the appliance body.
OUTLET EPA E10 FILTER AND FOAM FILTER III
The EPA E10 outlet filter should be replaced after about 30
hours of operation (6 months) or earlier in case of heavy dirt.
1
Remove the tank from the vacuum cleaner.
2
Place the vacuum cleaner with the “wheels upwards” so
that the upper sloping surface and the handle are rested on
the floor.
3
Slide the slider of the filter cover interlock to the “open”
position and remove the filter lid.
4
Remove the foam filter III
(12)
. Rinse or replace if the filter
becomes dirty. Remember to dry the filter before reassembly.
5
Remove the foam filter III
(12)
and next remove the
EPA E10 filter by grabbing the handle. Replace with a new
one if the filter becomes dirty.
It is recommended to periodically inspect the condition of the
filter, especially if there was a water overflow to the outside of
the vacuum cleaner. In case of detecting damage (a break)
in the filter layer or if the layer is evenly covered with dust,
the filter should be replace with a new one.
6
If the EPA E10 filter is dirty, replace it with a new one or
rinse under running water. Remember to dry the filter before
reassembly.
7
Reinsert the filters, insert the filter lid and press firmly.
8
Slide the slider of the filter cover interlock to the “closed”
position.
Turn the vacuum cleaner to its natural position (on four
wheels).
Disposal
Dispose of packaging in an environmentally-
friendly manner. This appliance is labelled
in accordance with European Directive
2012/19/EU concerning used electrical and
electronic appliances (waste electrical and
electronic equipment – WEEE). The guideline
determines the framework for the return and recycling of
used appliances as applicable throughout the EU. Please
ask your specialist retailer about current disposal facilities.
I
Summary of Contents for ZVC722 Series
