Zelmer ZCK8030 User Manual Download

Page: 6 / 35

This appliance is intended to be used in household. It is not

intended to be use in applications such as: -staff kitchen areas

in shops, offices and other working environments;
-farm houses;
-by clients in hotels, motels and other residential type

environments;
-bed and breakfast type environments.
Never immerse the appliance in water or any other liquid.
If the kettle is overfilled, boiling water may be ejected.
Appliance is only to be used with the stand provided.
Warning: avoid spillage on the connector
Warning: potential injury from misuse!
Heating element surface is subject to residual heat after use.
Allow the kettle to cool completely before cleaning.
Always remove the plug from the mains before cleaning the

kettle.
Do not use any abrasive cleaning agents – such as emulsions,

creams, pastes, etc. – for cleaning the kettle.
This appliance is intended for use at a maximum altitude of

2000m above sea level.

IMPORTANT WARNINGS

Any incorrect use or improper handling of the product shall render the warranty null and void.
Prior to plugging in the product, check that your mains voltage is the same as the one indicated on the product

label.
The mains connection cable must not be tangled or wrapped around the product during use.
Do not use the device, or connect and disconnect to the supply mains with the hands and / or feet wet.
Do not pull on the connection cord in order to unplug it or use it as a handle.
Only fill the kettle with water. Milk and instant beverages will burn and damage the appliance. Never operate the

kettle without water and do not over fill it; observe the min and max markings. If the kettle is too full, the water

will boil over!
Do not put the jug on a stove or in a microwave for re-heating of water.

Always place the kettle on a stable, smooth, flat surface; the power cord must not hang loosely off the edge of a

table (or any other work surface) or touch a heated surface.
Do not use the kettle with the lid open.
Do not remove the lid when the water is boiling.
If the internal electrical elements are flooded with water, make sure the kettle is completely dry before plugging in.
Do not move while the kettle is switched on.
Unplug the product immediately from the mains in the event of any breakdown or damage and contact an official

technical support service. In order to prevent any risk of danger, do not open the device. Only qualified technical

personnel from the brand´s Official technical support service may carry out repairs or procedures on the device.

B&B TRENDS SL. disclaims all liability for damages that may occur to people, animals or objects, for the non-

observance of these warnings.

INSTRUCTIONS FOR USE

Before use
Make sure that all the product’s packaging has been removed.
Before heating water for the first time, we recommend using the kettle twice, in order to clean the system.

Boiling water

1. Open the lid. Fill the kettle through the lid opening with a minimum of 500ml (2 cups) of water.
2. DO NOT attempt to fill the kettle it is plugged into the wall outlet.

DO NOT use for other than boiling water. Other liquids will contaminate the interior of the kettle.

DO NOT fill past the MAX level printed on the glass. Overfilling may cause water to spit out when boiling.

3.  Close the lid.
4.  Place kettle and base on a flat, level, dry, heat resistant surface. Ensure that it is correctly engaged on the base.
5.  Plug in to a wall outlet. The display will show the actual water temperature. The kettle is now in standby mode.

NOTE: if no selection has been made in 30 sec., the display will shut off and the kettle will enter sleep mode.

Press any button once to “wake up: the kettle.

6. Direct kettle spout away from cabinets, walls etc. to prevent possible steam damage.
7. The default temperature is 100°C (212°F). The variable temperature range is 40 to 100°C (105-212°F) in 10

degree C increments.

8. To boil water :

•

Press the power button

once.

•

To switch between the C and F display press the °C/°F button for 3 sec.

•

The display will show 100°C (212°F) for 3 sec. then the display will switch to the actual water

temperature. The display temperature will increase until the kettle reaches 100°C (212°F).

•

Once the water has boiled the kettle will shut off.