45
VC7920-003_v01
31
Foam filter II
32
Inlet filter
33
Motor filter
34
HEPA outlet filter
Preparing the vacuum cleaner for
operation
1
Insert the end of the suction hose to the vacuum cleaner
opening so that the markings on the hose end and on the
vacuum cleaner housing are opposite each other and turn
the hose clockwise to the position .
2
Connect the other end of the hose (handle) with the
telescopic suction tube.
3
Hold the ring on the pipe and set chosen length putting it
in or out.
4
Assemble the appropriate nozzle or brush to the other
end of the suction tube.
5
Use the following nozzles and brushes for traditional
vacuum cleaning with the SAFBAG dust bag and vacuum
cleaning with the use of the water filter module: combination
brush with small item separator, small nozzle, small brush,
crevice nozzle, parquet brush or turbo brush.
6
You may assemble a basket for picking up small objects
in the combination brush with small item separator. In order
to do so remove the basket cover and insert the basket.
7
To clean hard surfaces – wooden floors, plastic floors,
ceramic tiles etc. pull out the brush by pressing the switch on
the nozzle according to the figure
.
8
The vacuum cleaner is equipped with an accessory
compartment. The compartment opens/closes with the use
of a slider. To open/close the compartment side the slider
downwards/upwards and take out/ put away the desired
nozzle.
9
The vacuum cleaner may be stored in a horizontal
position; in order to this, place the fastening hook of the
combination nozzle/brush into its fastening. The hose may
be left attached to the vacuum cleaner, but it is important to
pay attention not to leave it heavily bent during storage.
10
Close the lid.
11
Grab the plug
(4)
and pull the cord out of the vacuum
cleaner.
While pulling out the cord pay attention to the
yellow stripe which signals the end of the cord.
Further attempts (pulling on cord) may result in
damaging the cord.
●
Plug in the appliance.
Before switching on the vacuum cleaner
with the on/off button (8), make sure that the
appropriate module is installed in the container
(see section C, E, or F).
B
12
Switch on the vacuum cleaner by pressing the “on/off”
button
(8)
.
In order to prepare the vacuum cleaner for wet operation
additionally:
13
Assemble the spray unit – the suction hose handle
attachment
(24)
.
●
Attach the hose fastenings to the suction hose and the
telescopic suction tube.
14
Attach the end of the hose (sleeve) to the telescopic
suction tube and insert the other end of the hose in the small
atomizing nozzle or the large atomizing nozzle until you hear
a characteristic click.
15
Use the following nozzles for the wet vacuuming and wet
cleaning function or to pick up water: large atomizing nozzle,
small atomizing nozzle or the water pick up nozzle.
16
Slide the stub pipe valve plug downwards.
●
Insert the stub pipe of the hose to the valve in the
vacuum cleaner housing.
●
Make sure the stub pipe fastenings snap shut.
In case of difficulties in connecting the above
mentioned elements moisten the gaskets e.g.
with technical vaseline, water, etc.
Vacuum cleaner functions
TRADITIONAL CLEANING WITH SAFBAG DUST BAG
1
Press and hold the container lid opening button
(2)
and
lift the container lid.
2
Remove the water filter module from the container
(filtration unit and partition).
3
Insert the dry filtration module with the SAFBAG
(21)
dust bag to the container.
●
Prepare the vacuum cleaner for operation according
to section B.
4
The vacuum cleaner starts at the same power level it had
been working before it was turned off. Set the desired power
value (this function is only available in vacuum cleaners type
VC7920.0) by pressing the power adjustment b/-
(9)
.
The vacuum cleaner is equipped with a power
level memory function. It is only available
in type VC7920.0 models. When you turn off
the vacuum cleaner using the ON/OFF button
(8), the power level is going to be stored in
memory. After the vacuum cleaner is turned
on next time, it is going to start working at the
same power level it had been working before it
was turned off.
The vacuum cleaner is equipped with the
adjustment function for LED brightness of
the power level indicator (10) and the clogged
air inlet indicator (12) situated on the control
panel. This function is available only in vacuum
C
