Zelmer 32z010-001, User Manual

Page: 41 / 44

45
32Z010-001_v04
●
Do not fill the jug over 1250 ml mark – in such case, the
content of the jug can lift the lid when the motor starts up.
●
It can be operated not longer than 3 minutes, without
interruption in constant or pulsating mode (“ Pulse ” and
“ Ice Crush ” features), otherwise it can get overheated.
After 3 minutes of operation, switch off the appliance
for at least 10 minutes, and let the motor cool down.
●
Do not operate when the jug is empty, as it can get
overheated.
●
The appliance is designed for use only in households
located up to 2000 m above sea level.
6 “ Off ” switch
7 “ Pulse ” switch
8 Handle
9 Blocking ring
10 Blades
11 Gasket
12 Motor housing
13 Speed control knob
14 “ Ice Crush ” button
15 Anti-slip flange
Handling and operation
PREPARATION FOR OPERATION
Before first usage (or after long storage) wash the jug (3) ,
lid (2) and feeder opening stopper (1) in hot water with
washing-up liquid, rinse and dry well. Keep your hands away
from cutting blades (10) – they are sharp.
OPERATION MANUAL
1
Place the motor housing (12) on dry, firm, and horizontal
surface, near mains supply outlet and out of the reach of
children.
Arrange the supplying cord so that it does not hang from
the table or board and it can not be pulled or dragged by
accident.
2
Connect the plug into the mains supply outlet.
3 Place the jug (3) so, that the protrusions at the bottom
part of the jug (3) were fitted with the protrusions in top part
of motor housing (12) .
The handle (8) of the blender jug (3) shall be
placed on the right side of the appliance.
4 Put the ingredients into the jug (3) . Do not fill in over
1250 ml marked on the blender jug (3) . In such case, the
content of the jug can lift the lid (2) when the motor starts up.
5 Insert the lid (2) on the jug (3) before you use the stand
blender.
6
Turn the lid (2) counter-clockwise (“ Lock ” position) until
it stops in the cut in the top part of the handle (8) . Make sure,
that the lid (2) is properly inserted in blender jug (3) it means
that the protrusion at the lid (2) is aligned with the handle
(8) , otherwise remove it and assemble once again. When
the lid is properly assembled, the control light (4) shall glow
pulsating which means that the appliance is ready for use.
Before you insert the lid (2) moisture the lid
gasket with water.
The motor driver is equipped with micro-
switch, which enables the appliance operation
only when the lid (2) is properly closed on the
blender jug (3). Otherwise the motor shall not
start up.
B
Safety recommendations
The stand blender has thermal protection, which turns off
the device at the moment of overheating. In this case, it is
necessary to disconnect the device from the power source.
Remove the plug from the contact, then wait at least 10
minutes, allowing the motor to cool down. After this time, you
can re-attach the stand blender.
Technical parameters
You can find the appliance technical data on the name plate.
Admissible time of non-stop operation: 3 minutes.
An interval between repeated operations: 10 minutes.
Speed range: 1-14.
Noise level at gear 14: 90 dB/A.
Appliance elements
1 Feeder opening stopper
2 Lid
3 Blender jug
4 Control light
5 “ On ” switch
A
TIP
Product information and tips
for use
●
This appliance is intended to be used in household and
similar applications such as:
●
staff kitchen areas in shops, offices and other
working environments;
●
farm houses;
●
by clients in hotels, motels and other residential
environments;
● bed and breakfast type environments.
In case it is used for gastronomic business purposes,
warranty terms and conditions change.
●
During first start-up the appliances can emit some
odours. It is a normal phenomenon, which should be
over after a time.