background image

 

 

 

 

 
 
2  

07/05 

Contents 

Page 

Starting the System ................................................................................................................3

 

Setting the microscope...........................................................................................................6

 

Configuring the beam path and lasers..................................................................................8

 

Scanning an image ...............................................................................................................11

 

Storing an image ..................................................................................................................15

 

Switching off the system .....................................................................................................15

 

 
 
 
 

 
 

Introduction 

 

 

For your safety!  
Observe the following instructions: 

− 

The LSM 510 and LSM 510 META laser scanning microscope, including its original 
accessories and compatible accessories from other manufacturers, may only be used for 
the purposes and microscopy techniques described in this manual (intended use). 

− 

In the Operating Manual, read the chapter 

Safety Instructions

 carefully before starting 

operation.  

− 

Follow the safety instructions described in the operating manual of the microscope and 
HBO 100 mercury lamp. 

 

Summary of Contents for LSM 510 Inverted

















Reviews: