ZCS 3000TLM LITE User Manual Download Page 62

Page: 62 / 64

62 / 64

Identificazione: MD-AL-GI-00
Rev. 4.0 del 31.01.18 - Applicazione: GID

Manual of 07/06/2019 Rev. 2.1 “User Manual for 3K-6KTLM LITE



Unscrew the fixing bolt of the bracket and remove the inverter from the wall.

8.2.

Packaging

If possible, pack the inverter in its original packaging.

8.3.

Storage

Store the inverter in a dry place where the ambient temperature is between -25 and +60°C.

8.4.

Disposal

At the end of its life, dispose of the inverter and the packaging materials in places that can manage and

recycle electrical equipment safely.

Technical specifications

3000TLM-

3600TLM-

4000TLM-

4600TLM-

5000TLM-

6000TLM-

Input (DC)

Typical power of PV system

3500W

4000W

4400W

5000W

5500W

6600W

Maximum DC power for each

MPPT

2000W

(160V-

520V)

2400W

(180V-

520V)

2600W

(200V-

520V)

3000W

(250V-

520V)

3000W

(250V-

520V)

3500W

(300V-

520V)

Number of independent

MPPTs

Number of DC inputs

1 for each MPPT

Maximum DC input voltage

600V

Input activation voltage

120V

Rated DC input voltage

360V

MPPT DC voltage range

90V-580V

DC voltage range at full load 160V-520V 180V-520V 200V-520V 230V-520V 250V-520V 300V-520V

Max input DC current for each

MPPT

11 A / 11 A

Output (AC)

Rated AC output power

3000W

3680W

4000W

4600W

5000W

6000W

Maximum AC power

3000VA

3680VA

4000VA

4600VA

5000VA

600

0VA

Maximum AC current

13.7 A

16.8 A

18.2 A

21A

22.8A

27.3A

Rated AC voltage

L/ N/ PE,220, 230, 240 V

Rated AC voltage range

180V-270V (According to local grid standards)

Rated grid frequency

50 / 60 Hz (According to local grid standards)

Frequency range

47-53Hz / 57-63 Hz (According to local grid standards)

Active power adjustable range

0-100%

Total harmonic current

distortion

Summary of Contents for 3000TLM LITE

































































Search results

Summary of Contents for 3000TLM LITE

Reviews:

Brands by name

Popular brands

ZCS 3000TLM LITE, User Manual

Search results

Summary of Contents for 3000TLM LITE

Reviews:

Brands by name

Popular brands