manualshive.com logo in svg

ZCS 3000TLM LITE, User Manual

Share
Download
ZCS 3000TLM LITE User Manual Download Page 38

 

          38 / 64 

Identificazione: MD-AL-GI-00 
Rev. 4.0 del 31.01.18 - Applicazione: GID 

Manual of 07/06/2019 Rev. 2.1 “User Manual for 3K-6KTLM LITE 

6.

 

Operating interface

 

General information in this chapter

 

This section describes the display and its operation, as well as the buttons and LED indicators of the 3K-6K 
TLM-L inverters.

 

6.1.

 

Operating panel and display 

 

Buttons and LED indicators

 

 

Figure 43 – LCD display with buttons and LED indicators

 

Main buttons: 

 

Menu/Back: to go back or enter the main menu. 

 

Up: to go up or increase the value by 1. 

 

Down: to go down or decrease the value by 1. 

 

OK/Enter: to confirm the selection and enter the menus 

 

Indicator lights: 

 

Status light (GREEN) 

o

 

Flashing: wait or status check  

o

 

Steady: normal operation 

o

 

Off: temporary or permanent error 
 

 

Warning light (RED) 

o

 

Steady: temporary or permanent error 

o

 

Off: normal operation 
 

 

GFCI automatic differential circuit breaker indicating light (RED) 

o

 

Steady: indicates GFCI fault  

o

 

Off: normal operation 

 

 

Summary of Contents for 3000TLM LITE

































































Reviews:

No comments

Brands by name

Popular brands

Load more brands