manualshive.com logo in svg

ZCS 3000TLM LITE, User Manual

Share
Download
ZCS 3000TLM LITE User Manual Download Page 21

 

          21 / 64 

Identificazione: MD-AL-GI-00 
Rev. 4.0 del 31.01.18 - Applicazione: GID 

Manual of 07/06/2019 Rev. 2.1 “User Manual for 3K-6KTLM LITE 

 

Figure 12 - Steps for installing the inverter on the wall 

 

4.

 

 Electrical connections 

General information in this chapter

 

This  chapter  describes  the  electrical  connections  of  the  3K-6K  TLM-L  inverter.  Carefully  read  this  section 
before connecting the cables. 

NOTE:

 

Before making any electrical connections, ensure that the DC circuit breaker is switched off.  Please note that 
the capacitors in the inverter may remain electrically charged after the DC circuit breaker has been switched 

off. Therefore, it is necessary to wait at least 5 minutes to allow the capacitor to discharge completely. 
 

 

The inverter must be installed and serviced by professional technicians or electricians.  

Attention

 

 

 

The PV modules generate electricity when exposed to sunlight, which can pose a risk 
of electric shock.  Before connecting the DC input power cord, be sure to disconnect 

the strings via the appropriate circuit breakers. 
 

Danger 

Summary of Contents for 3000TLM LITE

































































Reviews:

No comments

Brands by name

Popular brands

Load more brands