manualshive.com logo in svg

ZCS 3000TLM LITE, User Manual

Share
Download
ZCS 3000TLM LITE User Manual Download Page 58

 

          58 / 64 

Identificazione: MD-AL-GI-00 
Rev. 4.0 del 31.01.18 - Applicazione: GID 

Manual of 07/06/2019 Rev. 2.1 “User Manual for 3K-6KTLM LITE 

user manual. If it is not correct, 

change it according to Section 6.3 (A) 

“10. Configuration of the Input Mode” 

of this manual. If the input mode is 

correct, turn off the “DC switch”, wait 

5 minutes, and then turn it back on 

again. Check that the fault is no longer 

present. If this is not the case, contact 

Technical Support 

ID29 

SwOCPInstant 

The grid current is too 

high. 

Internal fault of the inverter; turn off 

the “DC switch”, wait 5 minutes, and 

then turn it back on again. Check that 

the fault is no longer present. If this is 

not the case, contact Technical 

Support 

ID30 

SwBOCPInstant 

The input current is 

too high. 

Check if the input current is higher 

than the maximum input current 

allowed by the inverter, then check 

the input wiring; if both are correct, 

contact Technical Support. 

ID49 

ConsistentFault_VGrid 

The grid voltage 

sampling value 

between the master 

DSP and slave DSP is 

not suitable. 

ID49-ID55 are internal faults of the 

inverter; turn off the “DC switch”, 

wait 5 minutes, and then turn it back 

on again. Check that the fault is no 

longer present. If this is not the case, 

contact Technical Support 

ID50 

ConsistentFault_FGrid 

The grid frequency 

sampling value 

between the master 

DSP and slave DSP is 

not suitable. 

ID51 

ConsistentFault_DCI 

The current sampling 

value of the automatic 

differential circuit 

breaker (DCI) 

between the master 

DSP and the slave DSP 

is not the same. 

ID52 

ConsistentFault_GFCI 

The current sampling 

value of the automatic 

differential circuit 

breaker (DCI) 

between the master 

DSP and the slave DSP 

is not the same. 

ID53 

SpiCommLose 

SPI communication 

error between the 

master DSP and the 

slave DSP. 

ID54 

SciCommLose 

SCI communication 

error between the 

master DSP and the 

slave DSP. 

Summary of Contents for 3000TLM LITE

































































Reviews:

No comments

Brands by name

Popular brands

Load more brands