ZCS 1100TL-G3 Manual Download Page 11

Page: 11 / 69

1.1K~3.3KTL-G3

User manual

- 6 -

Product characteristics

Outlines of this chapter

Product dimensions

It introduces the field of use, and the overall dimensions of 1.1K~3.3KTL-G3

inverters.

Function description

It introduces how 1.1K~3.3KTL-G3 inverters work and the function modules

inside.

Efficiency curves

It introduces the efficiency curves of in the inverter.

2.1.

Product dimensions

1.1K~3.3KTL-G3 is a single MPPT grid-tied PV inverter which converts the

DC power generated by PV arrays into sine wave single-phase AC power and feeds

it to the public electrical grid, AC circuit breaker (refer to Section 4.4) and DC

switch used as disconnect device, and the disconnect device shall be easily

accessible.

Figure2-1 PV Grid-tied System

1.1K~3.3KTL-G3 inverters can only be used with photovoltaic modules that

do not require one of the poles to be grounded. The operating current during normal

Summary of Contents for 1100TL-G3






































































Search results

Summary of Contents for 1100TL-G3

Reviews:

Related manuals for 1100TL-G3

Brands by name

Popular brands

ZCS 1100TL-G3, Manual

Search results

Summary of Contents for 1100TL-G3

Reviews:

Related manuals for 1100TL-G3

Brands by name

Popular brands