ZCS 1100TL-G3 Manual Download Page 8

Page: 8 / 69

1.1K~3.3KTL-G3

User manual

- 3 -

Sistemi S.p.A. for help if necessary.

Transport of the equipment, especially by road, must be carried out with by suitable

ways and means for protecting the components (in particular, the electronic

components) from violent shocks, humidity, vibration, etc.

Electric connection

Please comply with all the current electrical regulations about accident

prevention in dealing with the solar invert.

Before the electrical connection, make sure to use opaque

material  to  cover  the  PV  modules  or  to  disconnect  PV  array  DC
switch.  Exposure  to  the  sun,  PV  array  will  produce  a  dangerous
voltage!

Danger

All installation accomplished only by professional electrical

engineer!

Must be trained;
Completely read the manual operation and understand

relevant matter.

Warning

Get permission from the local electrical gird operator,

complete all electrical connections by professional electrical
engineer, then connect inverter to electrical grid.

Attention

It’s forbidden to remove the tamper evident label, or open the

inverter. Otherwise our company will not provide warranty or
maintenance!

Note

Operation

Touching the electrical grid or the terminal of the equipment

may lead to electrocution or fire!

Don’t touch the terminal or conductor connected to the

electrical grid.

Pay attention to any instructions or safety documents related to

grid connection.

Danger

Some internal components will be very hot when inverter is

working. Please wear protective gloves!

Attention

Maintenance and repair

Summary of Contents for 1100TL-G3






































































Search results

Summary of Contents for 1100TL-G3

Reviews:

Related manuals for 1100TL-G3

Brands by name

Popular brands

ZCS 1100TL-G3, Manual

Search results

Summary of Contents for 1100TL-G3

Reviews:

Related manuals for 1100TL-G3

Brands by name

Popular brands