ZCS 1100TL-G3 Manual Download Page 46

Page: 46 / 69

1.1K~3.3KTL-G3

User manual

- 41 -

Commissioning of inverter

5.1.

Safety inspection before commissioning

Ensure that DC and AC voltages are within the acceptable range of the

inverter.

Attention

5.2.

Start inverter

Step 1:

Turn ON the DC switch.(optional)

Step 2:

Turn ON the AC circuit breaker.

When the DC power generated by the solar array is adequate, the

1.1K~3.3KTL-G3 inverter will start automatically. Screen showing

“

normal

”

indicates correct operation.

NOTE:

Choose the correct country code. (refer to section 6.3 of this manual)

Notice:

Different distribution network operators in different countries have different

requirements regarding grid connections of PV grid connected inverters.

Therefore, it's very important to make sure that you have selected the correct

country code according to requirements of local authority.Please consult qualified

electrical engineer or personnel from electrical safety authorities about this.

Zucchetti Centro Sistemi S.p.A. is not responsible for any consequences

arising out of incorrect country code selection.

If the inverter indicates any fault, please refer to Section 7.1 of this manual

—

trouble shooting for help.

Summary of Contents for 1100TL-G3






































































Search results

Summary of Contents for 1100TL-G3

Reviews:

Related manuals for 1100TL-G3

Brands by name

Popular brands

ZCS 1100TL-G3, Manual

Search results

Summary of Contents for 1100TL-G3

Reviews:

Related manuals for 1100TL-G3

Brands by name

Popular brands