Z3 Technology Z3-HE4K-01 User Instructions Download Page 8

Page: 8 / 49

DOC-USR-0056-09

___________________________________________________________________________________________

Z3 Technology, LLC

♦

100 N 8

ST, STE 250

♦

Lincoln, NE 68508-1369 USA

♦

+1.402.323.0702

4.0

FEATURES



Encode up to 3840 x 2160 at 30fps H.264 + AAC



29.97, 25, 24 and 23.98fps capture also supported



Output to MPEG-2 TS, RTP or RTMP stream through GigE Ethernet



Supports simultaneous encode of a single 4K source into two different resolutions



Supports camera control via USB connection, including VISCA protocol compatible cameras



Multicast or Unicast streaming



Optional output to TS file on USB or SATA2



Bitrate and frame rate changes without stopping/restarting encoder



HTTP-based configuration software for user-friendly configuration, control, and update



Operating temperature: 0 to 40 degrees C at 20-80% relative humidity



Storage temperature: -10 to 65 degrees C at 20-80% relative humidity



Measurements: 145 x 130 x 34 mm (5.71 x 5.12 x 1.34 in)



Weight: 608 g (1.34 lb)

Supported Single Stream Encode Resolutions

4.1

HDMI:

2160p30, 2160p29.97, 2160p25, 1080p30, 1080i30, 1080i29.97, 1080i25, 720p60,
720p59.94, 720p50, 720p30, 720p29.97, 720p25, 576p50, 576i25, 480p60, 480i30, and
480i29.97

Supported Multi-Stream Encode Resolutions (Optional Upgrade)

4.2

The Z3-HE4K-01 is also available with a software upgrade that supports simultaneous encode of a single

4K source into two different resolutions and bitrates. Supported simultaneous stream encode
resolutions:

HDMI:

2160p30 and 720p30

2160p29.97 and 720p29.97

2160p25 and 720p25

Supported Decode Resolutions

4.3

HDMI:

2160p30, 2160p29.97, 2160p25, 1080p30, 1080i30, 1080i29.97, 1080i25, 720p60,
720p59.94, 720p50, 576p50 and 480p60

Software upgrade available. Contact Z3 for more information.

Only SATA2 drives are supported.

Summary of Contents for Z3-HE4K-01


















































Search results

Summary of Contents for Z3-HE4K-01

Reviews:

Related manuals for Z3-HE4K-01

Brands by name

Popular brands

Z3 Technology Z3-HE4K-01, User Instructions

Search results

Summary of Contents for Z3-HE4K-01

Reviews:

Related manuals for Z3-HE4K-01

Brands by name

Popular brands