Z3 Technology Z3-HE4K-01 User Instructions Download Page 41

Page: 41 / 49

DOC-USR-0056-09

___________________________________________________________________________________________

Z3 Technology, LLC

♦

100 N 8

ST, STE 250

♦

Lincoln, NE 68508-1369 USA

♦

+1.402.323.0702

The Term Tab (Not Supported - Available by Optional Software Upgrade)

10.5

Parameter

Options (default in bold)

Notes

Mode

Server

Client

Server is the default setting for camera
control

Protocol

Clear Channel

Telnet

Clear Channel is the default setting for
camera control

Baudrate

300 –

115200

9600 is recommended for camera control

Local Port

1000

Port on Z3-HE4K-01 for USB connection

Devicefile

/dev/tty02

Location path on the Z3-HE4K-01.  Enter the
following for either USB port on the
encoder:
USB1 (Top):  /dev/ttyUSB0
USB2 (Bottom):  /dev/ttyUSB1

The CH1 Tab (Encode Options)

10.6

Parameter

Options (default in bold)

Notes

Encoder Setup

Video Source

HDMI

The input source. Only HDMI is supported in
the Z3-HE4K-01.

Video Resolution

Follow Input

The encode resolution will be based on the
detected video input resolution.

Video Bitrate

6000K – 50000K (

15000K

)

4000K – 8000K

The recommended bitrate for 4k content is
6000k to 20000k.
The recommended bitrate for 1080p60
content is 4000k to 8000k.
Maximum Recommended Bitrates for
Multistream:
4K stream: 50000K
720p30 stream: 20000K

Video Profile

High

The H.264 profile of the bitstream.

Summary of Contents for Z3-HE4K-01


















































Search results

Summary of Contents for Z3-HE4K-01

Reviews:

Related manuals for Z3-HE4K-01

Brands by name

Popular brands

Z3 Technology Z3-HE4K-01, User Instructions

Search results

Summary of Contents for Z3-HE4K-01

Reviews:

Related manuals for Z3-HE4K-01

Brands by name

Popular brands