Z3 Technology Z3-DME-01 User Instructions Download Page 36

Page: 36 / 39

CONFIDENTIAL

DOC-USR-0018-09

____________________________________________________________________________________

Z3 Technology, LLC

♦

100 N. 8th St. STE 250

♦

Lincoln, NE 68508-1369 USA

♦

+1.402.323.0702

9.2

Decoder Options

Parameter

Options (default in bold)

Notes

Input Interface

Ethernet

DVB-ASI

Where to get the input stream to decode.

Input Format

RTP

RTSP
MPEG-2 TS
MPEG-2 TS over RTP

The format of the incoming stream. These

mirror the options on the encode side.

There is also an RTSP option. RTSP is used

in sources such as VLC and the TI IP Network

Camera.

RTP IP: Port

x.y.z.w:pppp (

225.1.2.3:8888

)

The IP address and port being streamed to.

Video Codec

H.264

The video format being used in the incoming

stream. Only H.264 is supported in this

release.

Audio Codec

AAC

MPEG
PCM
None

The audio codec being used in the incoming

stream. MPEG decodes MP1L2 and MP3.

Available options depend on what was

licensed.

MVE Flag

Yes

Set this flag if the streaming source is

another Z3-DME-01, the Z3-MVPR-01, the Z3-

MVE-20 or the Z3-MVE-02.

Output Interface

SDI

Only SDI output is supported.

Video Frame Rate

50Hz

60Hz

Use to select between NTSC and PAL

monitors, for example.

Local IP Address

192.168.X.XX (

192.168.0.65

)

Sets the IP address of the Z3-DME-01.
Disregarded if “Use DHCP” is checked.

Local Netmask

255.255.X.X (

255.255.0.0

)

Sets the Netmask of the Z3-DME-01.
Disregarded if “Use DHCP” is checked.

Default Gateway

192.168.X.XX (

192.168.0.1

)

Can generally leave as “192.168.0.1”
Disregarded if “Use DHCP” is checked.

Stop Decoder
[Button]

-----

Stop the current decode session.

Use DHCP
[Checkbox]

On /

Off

On -> Use DHCP to get IP address at boot-up

(see “Using DHCP”).

Start Decoder
[Button]

-----

Start a decode session.

Status

IDLE

, STOPPED, RUNNING

Current status of the decoder.

Load Factory Default
Settings [Button]

-----

Load settings installed at the factory.

Load User Settings

-----

Load user settings previously saved.

Save User Settings

-----

Save current settings for later use.

Summary of Contents for Z3-DME-01








































Search results

Summary of Contents for Z3-DME-01

Reviews:

Related manuals for Z3-DME-01

Brands by name

Popular brands

Z3 Technology Z3-DME-01, User Instructions

Search results

Summary of Contents for Z3-DME-01

Reviews:

Related manuals for Z3-DME-01

Brands by name

Popular brands