manualshive.com logo in svg

YSI 3200, Operation Manual

Share
Download
YSI 3200 Operation Manual Download Page 8

Introduction  

Section 

1 

The 3200 has two main operating modes, Data and Operation. The current mode is displayed in 
the dark bar at the top right corner of the display. The following diagram shows the typical 
display while the instrument is in the Operation mode. 

 

 

 

 

1.953

u

S

/cm

 

 
 
K=10.100 
25.0°C 

11:33

AM

 24.38°

C

 

1.91%/°C 
T  CELL 

MESSAGES DISPLAYED HERE 

CELL 

SETUP 

DIAGNOSTICS 

RANGE 

 

 

 

 

Conductance:  S 

mS 

uS 

Conductivity:  S/cm 

mS/cm 

uS/cm 

Resistance:  

Ω

 

K

Ω

 

M

Ω

 

Resistivity:  

Ω

cm 

K

Ω

cm 

M

Ω

cm 

Salinity:  ppt 

TDS:  mg/L 

Temperature:  °C 

Operation 

Temperature 

compensation 

data

Cell constant 

Mode

Temperature 

source

Soft key

functions

Message line 

The bottom row of the display identifies the function of the four soft keys, which are located on 
the keypad below the display. The function of each of these keys changes with each mode. 

The [Mode] key and soft keys are used to navigate through the menus. The [Mode] key is used to 
cycle between the two main operating modes. Pressing a soft key will bring up a new set of soft 
key functions (menu). The [Mode] key is also used to backup through the menus to the top level. 

The right side of the display shows the cell constant, temperature compensation data and current 
temperature source. 

K= 10.100 indicates that a single fixed cell constant of 10.100 is being used. K= would change to 
Km= when using multipoint calibration. 

25.0°C indicates that readings are temperature corrected to 25°C using a coefficient of 1.91%/°C, 
as indicated just below on the screen. When non-linear temperature compensation is used, N.L. is 
displayed here. When a standard non-linear curve is selected, the name of the curve (Pure, 
Natural) is displayed here. When no temperature compensation is being used, these two lines of 
the 3200 display are blank. 

T CELL indicates that the temperature source is a conductivity cell with an internal temperature 
sensor (YSI 3200 series). T PROBE is displayed when the temperature source is an external 
temperature probe. 

YSI Incorporated 

Model 3200 

4

 

 

Summary of Contents for 3200























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands