manualshive.com logo in svg

YSI 3200, Operation Manual

Share
Download
YSI 3200 Operation Manual Download Page 26

System Configuration and Operation 

 

Section 3 

1.  From Operation mode, press the [SETUP] soft key, then, press [SYSTEM] to enter the Setup                          
Sys menu. The following menu will be displayed. 

[Yes] key beep 

SETUP SYS 

 
[Off] alarm status 
[0.00]  low 

 

 

 

[Off] beep on alarm 

[0.00]  high 

 

 

 

[On] send on alarm 

[Conductance] uS alarm source 
 

UP 

DOWN 

DIGIT 

NEXT 

 

2.

 

Use the [NEXT] soft key to select the Alarm status field, then press [UP] or [DOWN] to 
change the Alarm status to “On”. 

3.

 

Press [NEXT] to select the Low field, then use the [UP], [DOWN] and [DIGIT] soft keys to 
enter the set point for the low alarm. 

4.

 

Press [NEXT] to select the High field and use the [UP], [DOWN] and [DIGIT] soft keys to 
enter the set point for the high alarm. 

5.

 

Press [NEXT] to select the alarm source, then press [UP] or [DOWN] to change the source. 
The source may be conductance, conductivity or resistance. 

6.

 

Press [NEXT] to select “beep on alarm”, then press [UP] or [DOWN] to turn the alarm beeper 
on or off. 

7.

 

Press [NEXT] to select “send on alarm”. When this parameter is enabled (On), readings will 
be sent to a computer or serial printer whenever the alarm is triggered. 

Press [MODE] once, to return to the Setup menu, or two times to return to Operation mode. 

NOTE: To setup the communications parameters or select the report format and which data fields 
will be sent over the RS232 serial port, see 4.3 Send, Send Setup. 

BEEPER 

The 3200 contains a beeper to indicate when a key has been pressed. The beeper may be turned 
on or off from the Setup Sys menu. Press the [SETUP] soft key, while Operation mode, then 
press [SYSTEM] to enter the Setup Sys menu . 

Beeper status 

 

[No] key beep 

SETUP SYS 

 
[Off] alarm status 
[0.00] alarm low   

 

 

[Off] beep on alarm 

[0.00] alarm high  

 

 

[On] send on alarm 

[Conductance] uS alarm source 
 

UP 

DOWN 

DIGIT 

NEXT 

 

YSI Incorporated 

Model 3200 

22

 

 

Summary of Contents for 3200























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands