background image

5284792-UIM-A-0317

12

Johnson Controls Unitary Products

MENU NOTES:

Discharge Pressure, Liquid Temperature, Suction Pressure, Suction
Temperature, Calculated Superheat, and Calculated Subcool. On the
high gauge display, the control shall toggle at a rate of 10 seconds
between the Liquid Temperature and the Subcool calculated value. On
the low gauge display, the control shall toggle at a rate of 10 seconds
between the Suction Temperature and the Superheat calculated value.

Time out period: While in the Menu Structure if the display does not
sense a navigational response within 5 minutes, the outdoor display will
return to General Display Operation.

Door Switch: If the outdoor display is in the Menu Structure and the
door switch is de-activated, the system will de-energizing the outdoor
screen. Upon re-energizing the outdoor screen, the display will return to
the General Display Operation.

Saved Configuration/Selection: The system will save all individual con-
figuration selections made on the Outdoor Display. Upon returning to a
previously saved configuration the system shall display the previously
saved configuration setting(s). Not the Default setting(s), unless the
saved selection was in fact the default selection.

Operational Mode: The system will display (Inverter profile and revers-
ing valve dependent) unit tonnage when the user selects Operational
Mode (AC).

TABLE 6: 

Outdoor Display Menu Structure

MAIN LAYER

SECOND LAYER

THIRD LAYER

BASE LAYER

EQUIPMENT STATUS

COMMANDED

COMPRESSOR (RPM)

OD FAN (RPM)

ID EEV (SP)

ID FAN (CFM)

CURRENT

COMPRESSOR (RPM)

OD FAN (RPM)

ID EEV (SP)

ID FAN (CFM)

INPUT CURRENT (AMPS)

INPUT VOLTAGE (VOLTS)

INPUT WATTS (WATTS)

CONFIGURATIONS

DEMAND RESPONSE

OFF (Default)

NORMALY OPEN RELAY

NORMALY CLOSED RELAY

INVERTER REPAIR PART

System will first determine Unit Type (Reversing Valve Presence) and Unit Tonnage 
(Inverter Configuration) and will walk the user through the operation, per inverter part num-
ber.

2-TON

3-TON

4-TON

5-TON

SOFT JUMPERS

COMFORT - EFFICIENCY

EFFICIENCY (Default)

COMFORT

MODES

FAULT MODE

CURRENT SYSTEM FAULTS

STORED SYSTEM FAULTS

CLEAR FAULT LOG

TEST MODE

BYPASS ASCD TIMER

OPERATIONAL MODE (AC)

System will display Unit Type (Reversing Valve Presence) and Unit Tonnage (Inverter Con-
figuration)

CHARGE VERIFICATION

System determines Unit Tonnage (Inverter Configuration) and will walk the user through 
the operation.

Summary of Contents for YXV series

























Reviews: