York YXV series Installation Manual Download Page 24

Page: 24 / 24

Subject to change without notice. Published in U.S.A.

5284792-UIM-A-0317

Supersedes: Nothing

York International Corp.

5005 York Drive

Norman, OK 73069

Measured Amperage

Measured Voltage

Heating return air

dry bulb temperature

Number

of elements

Heating supply air

dry bulb temperature

Air temperature rise

Single Phase

Subcooling

R-410A

Superheat

Discharge pressure

Data plate - lbs / Oz

Explain operation of system to equipment owner

Explain the importance of regular filter replacement and equipment maintenance

Clean Up Job Site

Owner Education

Comments and Additional Job Details

Provide owner with the owner's manual

Explain thermostat use and programming (if applicable) to owner

Unit Operation and Cycle Test

Operate the unit through continuous fan cycles from the thermostat, noting and correcting any problems

Operate the unit through cooling cycles from the thermostat, noting and correcting any problems

Job site has been cleaned, indoor and outdoor debris removed from job site

Tools have been removed from unit

All panels have been installed

Liquid line temperature

Total Static

Return Static

Supply Static

Suction pressure

Suction line temperature

Setup

WiFi enabled

Electric heat kit - Model number

Serial number

Rated KW

Heater 1

Heater 6

Heater 3

Heater 5

Heater 2

Heater 4

Heater 1

Heater 4

Heater 2

Heater 5

Heater 3

Heater 6

Electric Heat

Page 2 of 2 (3/14/17)

Discharge line

temperature

Yes

Demand response enabled For profile Normal

Arid

Humid

Summary of Contents for YXV series

























Search results

Summary of Contents for YXV series

Reviews:

Related manuals for YXV series

Brands by name

Popular brands

York YXV series, Installation Manual

Search results

Summary of Contents for YXV series

Reviews:

Related manuals for YXV series

Brands by name

Popular brands