York THGD Series Installation Manual Download Page 9

Page: 9 / 20

835961-UIM-D-0213

Johnson Controls Unitary Products

SECTION IX: SYSTEM START-UP

ENERGIZE CRANKCASE HEATER

If this unit is equipped with a crankcase heater for the compressor, a
warning label with an adhesive back is supplied in the unit installation
instruction packet. This label should be attached to the field supplied
disconnect switch where it will be easily seen.

In order to energize the crankcase heater, set the indoor cooling ther-
mostat to the OFF position. Close the line power disconnect to the unit.

WITH POWER TO UNIT AND THERMOSTAT IN COOLING
POSITION:

1. In the cooling cycle, discharge gas is pumped to the outdoor coil

which is the condenser. The indoor coil is the evaporator.

2. If fan switch is in ON position, a circuit is made through blower relay

to provide continuous blower operation.

3. With fan switch in AUTO position, a circuit is made from thermostat

cooling contact through blower relay to provide blower operation.

4. System will cycle with thermostat demand to provide cooling as

needed.

An attempt to start the compressor without at least 8 hours of crank-
case heat will damage the compressor.

TABLE 1:

R-410A Saturation Properties

Temp °F

Pressure

PSIG

Temp °F

Pressure

PSIG

Temp °F

Pressure

PSIG

Temp °F

Pressure

PSIG

Temp °F

Pressure

PSIG

130

170

217

274

105

341

132

173

221

278

106

345

135

176

224

282

107

350

137

179

228

287

108

355

140

182

232

291

109

360

142

185

235

295

110

365

145

188

239

299

111

370

147

191

243

304

112

375

150

194

247

308

113

380

153

197

250

313

114

385

156

201

254

100

317

115

391

158

204

258

101

322

116

396

161

207

262

102

326.

117

401

164

211

266

103

331

118

407

167

214

270

104

336

119

412

FIGURE 10:

Heat Pump Flow Diagram

CHARGE COMPENSATOR

(Empty in cooling / full in heating)

(Not included in all Units)

FIELD CONNECTED LINE

INDOOR COIL

OUTDOOR
COIL

4-WAY
REVERSING
VALVE

FILTER DRYER
(Solid core)

SUCTION
ACCUMULATOR

LIQUID
SENSOR

COMPRESSOR

BI-FLOW
TXV/CHECK
VALVE (Cooling) **

BI-FLOW
TXV/CHECK
VALVE OR ORIFICE (Heating)

Summary of Contents for THGD Series





















Search results

Summary of Contents for THGD Series

Reviews:

Related manuals for THGD Series

Brands by name

Popular brands

York THGD Series, Installation Manual

Search results

Summary of Contents for THGD Series

Reviews:

Related manuals for THGD Series

Brands by name

Popular brands