background image

GENERAL

YORK Model DEG units are single package high efficiency air
conditioners with gas heat designed for outdoor installation on
a rooftop or a slab.
The units are completely assembled on rigid, permanently
attached base rails. All piping, refrigerant charge, and electrical
wiring is factory installed and tested. The units require only
electric power and duct connections at the point of installation.
The gas-fired heaters have aluminized steel tubular heat
exchangers and spark ignition with proven pilot.

INSPECTION

As soon as a unit is received, it should be inspected for possible
damage during transit. If damage is evident, the extent of the
damage should be noted on the carrier’s freight bill. A separate
request for inspection by the carrier’s agent should be made in
writing. Refer to Form 50.15-NM for additional information.

REFERENCE

Additional information on the design, installation, operation and
service of this equipment is available in the following reference
forms:

55.70-N1          - General Installation

55.70-N2          - Pre-start & Post-start Check List

530.18-N3.2V   - Economizer Accessory

530.18-N3.4V   - Motorized Outdoor Air Damper Accy.

530.18-N8.4V   - Gas Piping Accessory

530.18-N10.1V - Propane Conversion Accessory (USA)

530.18-N10.2V - High Altitude Accessory (Nat. Gas)

530.18-N10.3V - High Altitude Accessory (Propane)

690.15-N25V    - Low Ambient Accessory

Renewal Parts:

Refer to the Renewal Parts Manual for complete listing of

replacement parts on this equipment.

All forms referenced in this instruction may be ordered from:

Publications Distribution Center

Unitary Products Group

P.O. Box 1592, York, Pa.  17405

APPROVALS

Design certified by U.L. as follows:

1. For use as a forced air furnace with cooling unit.

2. For outdoor installation only.

3. For installation on combustible material.

4. For use with natural gas or propane gas.

® 

SUNLINE PLUS

GAS / ELECTRIC

SINGLE PACKAGE AIR CONDITIONERS

INSTALLATION INSTRUCTION

Supersedes: 530.22-N4Y (693) 

530.22-N4Y (995)

MODELS D1EG090, & 120 (STYLE B)

 &  D2EG150

(9.5 - 10.0 EER)

035-13087

               

FOR YOUR SAFETY

Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance

.

         

    

  FOR YOUR SAFETY

If you smell gas:
1. Open windows.
2. Don’t touch electrical switches
3. Extinguish any open flame.
4. Immediately call your gas supplier.

Installer should pay particular attention to the words:  

NOTE, CAUTION and WARNING. Notes are intended to clarify or

make the installation easier. Cautions are given to prevent equipment damage. Warnings are given to alert installer that per-
sonal injury and/or equipment damage may result if installation procedure is not handled properly.

CAUTION

THIS PRODUCT MUST BE INSTALLED IN STRICT COMPLIANCE
WITH THE ENCLOSED INSTALLATION INSTRUCTIONS AND ANY
APPL ICABLE L OCAL , STATE, AND NATIONAL CODES
INCLUDING, BUT NOT LIMITED TO, BUILDING, ELECTRICAL,
AND MECHANICAL CODES.

WARNING

INCORRECT INSTALLATION MAY CREATE A CONDITION WHERE
THE OPERATION OF THE PRODUCT COULD CAUSE PERSONAL
INJURY OR PROPERTY DAMAGE

Summary of Contents for SUNLINE PLUS D1EG090





















Reviews: