background image

Cont’d.

All dimensions are in inches. They are
subject to change without notice. Certified
dimensions will be provided upon request.

CLEARANCES (mm / in.)

Front

914 / 36"

Back

610 / 24" (Less Economizer)
1245 / 49" (With Economizer)

Left Side (Filter Access)

610 / 24" (Less Economizer)
1372 / 54" (With Economizer)

Right Side (Cond. Coil)

914 / 36"

Below Unit

1

0 / 0"

Above Unit

2

1829 / 72" With  914 / 36" Maximum
      Horizontal Overhang
      (For Condenser Air
      Discharge)

1

Units (applicable in U.S.A. only) may be installed on combustible floors

  made from wood or class A, B or C roof covering material.

2

Units must be installed oudoors. Overhanging structures or shrubs should

  not obstruct condenser air discharge outlet.

NOTE:
DCE Models: Units and ductwork are approved for zero clearance to combustible mate-
rials when equipped with electric heaters.

DCG Models: A 1" clearance must be provided between any combustible
material and the supply air ductwork for a distance of 3 feet from the unit.

The products of combustion must not be allowed to accumulate within a
confined space and recirculate.

Locate unit so that the vent air outlet hood is at least:

Three (3) feet above any forced air inlet located within 10 horizontal feet (excluding
those integral to the unit).

Four (4) feet below, 4 horizontal feet from, or 1 foot above any door or gravity air inlet
into the building.

Four (4) feet from electric meters, gas meters, regulators and relief equipment.

HOLE

OPENING

(DIA.)

(mm / in.)

USED FOR

A

29 / 1-1/8" KO

Control
Wiring

Front

19 / 3/4" NPS

(Fem.)

Bottom

B

92 / 3-5/8" KO

Power Wiring

Front

76 / 3" NPS

(Fem.)

Bottom

C

60 / 2-3/8" KO

Gas Piping (Front)

D

43 / 1-11/16"

Hole

Gas Piping (Bottom)*

 *

Opening in the bottom of the unit can be located by the slice

   in the insulation.

RETURN AIR

SUPPLY AIR

CONDENSER AIR

OUTDOOR AIR
(Economizer)

DCE

UNITS

1337 (52-5/8")

       3461 (136-1/4")

DCG

UNITS

       3461 (136-1/4")

1337 (52-5/8")

UNIT DIMENSIONS -

 (DCE / DCG)

530.26-TG4YI

8

Unitary Products Group

Summary of Contents for Sunline 2000













Reviews: