background image

6

Mounting Installation Plate

Ensure that the wall is strong enough to withstand
the weight of the unit. Otherwise, it is necessary
to reinforce the wall with plates, beams or pillars.
Use the level gauge for horizontal mounting, and
fix it with 5 suitable screws.
In case the rear piping draws out, drill a hole
65mm in diameter with a cone drill, slightly
lower on the outside wall  (see figure).

Recommended Mounting Plate
Retention Spots And Dimensions

How To  Attach The Indoor Unit

Hook the claws of the bottom frame to the
mounting plate.

How To Remove The Indoor Unit

Push up the marked area (at the lower part of the
front grille) to release the claws.

Mounting plate

Mounting plate
fixing screw

Inside

Outside

Through
the wall
hole
Ø 65mm

Drain
hose
position

Recommended mounting
plate retention spots
(5 spots in all)

Use tape measure as shown.
Position the end  of a tape measure
at

Gas pipe end

Liquid pipe end

166

184

181.7

55.5

54.5

153.8

263

51.9

800

45.9

42.2

288

42.2

45.9

Hole with cone drill

All dimensions are in mm

Caulking

Wall embedded
pipe (Field
supply)

Wall hole cover
(Field supply)

Wall embedded pipe
(Field supply)

Ø 65

Mount The Unit Onto The Installation
Plate

Hook the indoor unit onto the upper portion of
the installation plate (Engage the two hooks at
the rear top of the indoor unit with the upper
edge of the installation plate). Ensure that the
hooks are properly seated on the installation plate
by moving it to the left and right.

Mounting
plate

Clip

Mark
(rear side)

Bottom frame

Front grille

Mounting
plate

Interconnecting
wires

Hang indoor unit’s hook here.

Wire guide

When stripping
the ends of
interconnecting
wires in advance,
bind right ends
of wires with
insulating tape.

Water Drainage Piping

The indoor drain pipe must be in a downward
gradient for smooth drainage. Avoid situations
that are likely to cause water to leak.

End
dipped
into
water

Water
leaking

Water
leaking

Water
leaking

Wrong

Wrong

Wrong

Drain

Water Drainage

Water
retention

Correct

Summary of Contents for J Series





















Reviews: