background image

13

English

AIR FILTER

1. Open the front panel.

• Hold the panel at the recesses on the main

unit (2 recesses on right and left sides) and
lift it until it stops.

2. Pull out the air filters.

• Push a little upwards the tab at the center

of each air filter, then pull it down.

3. Take off the Bio filter with

bacteriostatic, virustatic functions.

• Hold the recessed parts of the frame and

unhook the four claws.

4. Clean or replace each filter.

See figure.
• When shaking off remaining water, do not

wring the filter.

5. Set the air filter and Bio filter with

bacteriostatic, virustatic functions as
they were and close the front panel.

• Insert claws of the filters into slots of the

front panel. Close the front panel slowly and
push the panel at the 3 points. (1 on each
side and 1 in the middle.)

• The air filter and Bio filter with

bacteriostatic, virustatic functions have a
symmetrical form in the horizontal
direction.

FRONT

Recess on
main unit

Filter frame

Tab

Air filter

Bio filter with
bacteriostatic,
virustatic functions

Titanium Apatit Filter (Bio Filter)
Attached Concept

Air filter

Heat exchanger

Bio filter attached part

Titanium apatit filter

Installation Procedure for Bio filter

Bio filter packs in a
hermetically-sealed bag.

Take it out
at the time of installation.

Slip the filter in between filter frame
and Titanium apatite filter.

Titanium apatite filter

Bio filter

Filter frame

Summary of Contents for J Series





















Reviews: