background image

272312-UIM-A-0407

10

Unitary Products Group

SECTION V: ELECTRICAL POWER

Electrical Power Connections

Field wiring to the unit must be grounded. Electric wires that are field
installed shall conform to the temperature limitation of 63°F (35°C) rise
when installed in accordance with these instructions. Refer to Table 8 in
these instructions for specific furnace electrical data.

1. Annual Fuel Utilization Efficiency (AFUE) numbers are determined in accordance with DOE Test procedures.
2. Field wiring and over-current protection (Max Fuse Size) must conform to and be grounded in accordance ANSI/NFPA 

No. 70-latest edition or the Canadian Electrical Code C222.1 Part 1-latest edition and / or local codes.

3. Wire size based on copper conductors, 60º C, 3% voltage drop. "Unit Amps" refers to the full load current.
4. Min wire size (awg) @ 75 ft. one way refers to the minimum recommended field installed wire size.

PROPANE AND HIGH ALTITUDE CONVERSION KITS
It is very important to choose the correct kit and/or gas orifices for the altitude and the type of gas for which the furnace is being installed.
Only use natural gas in furnaces designed for natural gas. Only use propane (LP) gas for furnaces that have been properly converted to use pro-
pane (LP) gas. Do not use this furnace with butane gas.
Incorrect gas orifices or a furnace that has been improperly converted will create an extremely dangerous condition resulting in premature heat
exchanger failure, excessive sooting, high levels of carbon monoxide, personal injury, property damage, a fire hazard and/or death.
High altitude and propane (LP) conversions are required in order for the appliance to satisfactory meet the application.
An authorized distributor or dealer must make all gas conversions.
In Canada, a certified conversion station or other qualified agency, using factory specified and/or approved parts, must perform the conversion.
The installer must take every precaution to insure that the furnace has been converted to the proper gas orifice size when the furnace is installed.
Do not attempt to drill out any orifices to obtain the proper orifice size. Drilling out a gas orifice will cause misalignment of the burner flames,
causing premature heat exchanger burnout, high levels of carbon monoxide, excessive sooting, a fire hazard, personal injury, property damage
and/or death.

Use copper conductors only.

TABLE 8: 

Ratings & Physical / Electrical Data

Input

High/Low

Output BTU/H

High/Low

Nominal

Airflow

Cabinet Width

AFUE

Blower

Blower Size

MBH

kW

MBH

kW

CFM

m

3

min

In

cm

Hp

Amps

In

cm

40/26

11.7/7.6

32/21

9.4/6.1

1200

34.0

14-1/2

36.8

80.0

1/2

7.7

10 x 8

25.4 x 20.3

57/42

16.7/12.3

46/34

13.5/10.0

1200

34.0

14-1/2

36.8

80.0

1/2

7.7

10 x 8

25.4 x 20.3

80/59

23.4/17.3

64/48

18.8/14.1

1200

34.0

14 1/2

36.8

80.0

1/2

7.7

10 x 8

25.4 x 20.3

80/59

23.4/17.3

64/48

18.8/14.1

1600

45.3

17-1/2

44.5

80.0

3/4

11.5

10 x 10

25.4 x 25.4

80/59

23.4/17.3

64/48

18.8/14.1

1600

45.3

21

53.3

80.0

3/4

11.5

10 x 10

25.4 x 25.4

100/65

29.3/19.1

80/53

23.4/15.5

1200

34.0

17 1/2

44.5

80.0

1/2

11.5

10 x 10

25.4 x 25.4

100/65

29.3/19.1

80/53

23.4/15.5

2000

56.6

21

53.3

80.0

1

14

11 x 10

27.9 x 25.4

120/78

35.1/22.9

96/64

28.1/18.8

1600

56.6

21

53.3

80.0

3/4

11.5

11 x 10

27.9 x 25.4

120/78

35.1/22.9

96/64

28.1/18.8

2000

56.6

21

53.3

80.0

1

14

11 x 11

27.9 x 25.4

Input/Cabinet

High/Low

Max. Outlet 

Air Temp

Low Fire

Air Temp. Rise

High Fire

Air Temp. Rise

Total 

Unit

Amps

Max 

Over-Current 

Protect

Min. wire Size 

(awg) @ 75 ft 

one way

Operation 

Weight

MBH

kW

°F

°C

°F

°C

°F

°C

Lbs

 Kg

40/26

11.7/7.6

150

83.3

15-45

8-25

20-50

11-28

9.0

20

14

107

48.5

57/42

16.7/12.3

160

71.1

25-55

14-31

35-65

19-36

9.0

20

14

107

48.5

80/52

23.4/17.3

175

79.4

30-60

17-33

40-70

22-39

9.0

20

14

117

53.2

80/59

23.4/17.3

160

71.1

25-55

14-31

25-55

14-31

12.0

20

14

129

58.5

80/59

23.4/17.3

160

71.1

25-55

14-31

25-55

14-31

12.0

20

14

130

59.1

100/65

29.3/19.1

170

76.7

25-55

14-31

40-70

22-39

12.9

20

14

128

58.2

100/65

29.3/19.1

170

76.7

25-55

14-31

40-70

22-39

14.0

20

14

145

65.9

120/78

35.1/22.9

180

76.7

25-55

14-31

45-75

25-41

12.0

20

14

145

65.9

120/78

35.1/22.9

170

76.7

25-55

14-31

35-65

19-36

14.0

20

12

147

66.8

Summary of Contents for FC8T-UH

































Reviews: