background image

272312-UIM-A-0407

16

Unitary Products Group

CATEGORY 1 - 450 F. MAX. VENT TEMP.

The venting system must be installed in accordance with Section 5.3,
Air for Combustion and Ventilation, of the National Fuel Gas Code
Z223.1/NFPA 54 (latest edition), or Sections 7.2, 7.3 or 7.4 of CSA
B149.1, National Gas and Propane Codes (latest edition) or applicable
provisions of the local building code and these instructions.
The furnace shall be connected to any type of B, BW or L vent connec-
tor, and shall be connected to a factory-built or masonry chimney. 

The

furnace shall not be connected to a chimney flue serving a sepa-
rate appliance designed to burn solid fuel. 

The furnace rating plate lists the maximum vent gas temperature. This
temperature must be used to select the appropriate venting materials
and clearances. 
It is recommended that the appliance is installed in a location where the
space temperature is 32 °F (0°C) or higher. If the appliance is installed
in a location where the ambient temperature is below 32 °F (0°C), the
combustion by-products could condense causing damage to the appli-
ance heat exchanger.

IMPORTANT: 

The “VENT SYSTEM” must be installed as specified in

these instructions for Residential and Modular Homes.

This appliance may be common vented with another gas appliance for
residential installations as allowed by the codes and standards listed in
these instructions.
Approved Modular Homes must be vented with an approved roof jack
and may not be common vented with other appliances.

VENTING

Category I venting consists of vertically venting one or more appliances
in B-vent or masonry chimney (as allowed), using single wall metal pipe
or B-vent connectors. Type B-vent system extends in a general vertical
direction and does not contain offsets exceeding 45 degrees. A vent
system having not more than one 60 degree offset is permitted.
The vent system must be attached to the flue collar with a minimum of
two (2) mechanical fasteners, such as screws or rivets. See Figure 21.

 FIGURE 16:  

Vent Termination more than 10 ft. (3.0 m)

 FIGURE 17:  

Vent Termination

MORE THAN
10 FT (3.0 m)

3 FT (0.9 m)
MIN.

WALL OR
PARAPET

RIDGE

CHIMNEY

CHIMNEY

3 FT (0.9 m)
MIN.

2 FT (0.6 m)

MIN.

MORE THAN
10 FT (3.0 m)

NOTE:

NO

HEIGHT ABOVE
PARAPET REQUIRED
WHEN DISTANCE
FROM WALLS OR
PARAPET IS MORE
THAN 10 FT (3.0 m).

10 FT

(3.0 m)

HEIGHT ABOVE ANY
ROOF SURFACE WITHIN
10 FT (3.0 m) HORIZONTALLY

MORE THAN 10 FT (3.0 m)
FROM RIDGE, WALL,
OR PARAPET

*

*

*

LISTED CAP

LISTED GAS
VENT

LOWEST DISCHARGE OPENING

12

ROOF PITCH
IS x/12

H(min.) MINIMUM HEIGHT
FROM ROOF TO LOWEST
DISCHARGE OPENING

X

TABLE 9: 

Roof Pitch

ROOF PITCH

H(min) ft

m

Flat to 6/12

1.0

0.30

6/12 to 7/12

1.25

0.38

Over 7/12 to 8/12

1.5

0.46

Over 8/12 to 9/12

2.0

0.61

Over 9/12 to 10/12

2.5

0.76

Over 10/12 to 11/12

3.25

0.99

Over 11/12 to 12/12

4.0

1.22

Over 12/12 to 14/12

5.0

1.52

Over 14/12 to 16/12

6.0

1.83

Over 16/12 to 18/12

7.0

2.13

Over 18/12 to 20/12

7.5

2.27

Over 20/12 to 21/12

8.0

2.44

Summary of Contents for FC8T-UH

































Reviews: