background image

Yokogawa Electric Corporation - TC10-L - ENGINEERING MANUAL - PAG. 10

SP

HYS

PV

(A)

(B)

(C)

(A)

(B)

(D)

EXCEEDED

LAMP

OUT

LAMP

lit

off

OUTPUT

RELAY

confirmation

(accepted)

confirmation

(not accepted)

lit

off

Energized

De-energized

OFF

OFF

OFF

Lit

Lit

OFF

Lit

ON

OFF

ON

OFF

Lit

OFF

When the EXCEED lamp is ON but PV is Higher than SP, 
the upper display will be in green value and it shows that the 
PV is in the hysteresis area.

[34] r.md – Limit output status at power ON (Re-

start mode)

Available: 

Available: always

Range: 

0 =  

limit output is ON in any cas

1 =  

Limit output is OFF at power on when PV 
doesn’t exceed SP.

 

[35] HyS – Hysteresis of the control output 

Available: 

Available: always 

Range: 

In engineering unit from 0.0 to 100 % of the input 
span

[36] oP.SL – Operating display selection.

Available: 

Available: always

Range: 

Range: 

PU.SP  = (0) PV (upper display) and SP (lower 
display)

PU  

= (1) SP only (lower display)

Note: 

When you change the [37] SPLL value, the nstrument 
checks the local set points (SP parameters).  If SP 
is out of this range, the instrument forces it to the 
maximum acceptable value

[37] SPLL – Minimum set point value 

Available: 

Available: always 

Range: 

from -1999  to  [38] SPHL

Note: 

When you change the [37] SPLL value, the instrument 
checks the local set points (SP parameters). If  SP 
is out of this range, the instrument forces it to the 
minimum acceptable value.

[38] SPHL – Maximum set point value 

Available: 

Available: always 

Range: 

from [37] SPLL to 9999.

[39] SP  - Set point.

Available: 

Available: always

Range: 

from [37] SPLL to [38] SPHL

[40] diS– the way of confi rming operation

Available: 

Available: always

Range: 

but = 

by keyboard

di =  

by digital input

[41] tim – time duration of the last exceeded period. 

Available: 

Available: always but it is a read only parameter.

Range: 

from 00.00 to 99.59 (HH.mm).

[42] Hi- maximum measured value

Available: 

Available: when [33] Hi.Lo = Hi (high limit) but it is 
a read only parameter.

Range: 

Engineering unit within the input range

[43] Lo – minimum measured value

Available: 

Available: when [33] Hi.Lo = Lo (low limit) but it is 
a read only parameter.

Range: 

Engineering unit within the input range.

]

PAn group - Operator HMI

[44] PAS2 - Level 2 password: 

Available: 

Always.

Range: 

oFF = 

Level 2 not protected by password 
(as level 1 = Operator level) 1 to 200.

[45] PAS3  - Level 3 password: 

Complete confi guration level

Available: 

Always.

Range: 

3 to 200.

Note: 

Setting [44] PAS2 equal to [45] PAS3, the level 2 will 
be masked.

[46] di.CL - Display color

Available: 

Always.

Range: 

0 = 

the display color is used to show the 
Exceed condition. 

 

When no exceed condition is present, the 
upper display will be green.

 

when [33] Hi.Lo = Hi (high limit ) and PV > 
SP the upper display will be red.

 

when [33] Hi.Lo = Lo (low limit ) and PV < 
SP the upper display will be red.

1 = 

Display red (fi x);

2 = 

Display green (fi x);

3 = 

Display orange (fi x).

[47] diS.t - Display time out

Available: 

Always.

Range: 

oFF = 

The display is ever ON;

0 (OFF) to 99.59 minutes and seconds.

Note: 

This function allows to turn OFF the display when no 
alarm is present and no action is made on the instrument.
When diS.t is different from OFF and no button is 
pressed for more than the programmed time out, the 
display goes OFF and only 4 segments of the less 
signifi cant digit are turned ON in sequence in order to 
show that the instrument is working correctly.
If an alarm occurs or a button is pressed, the display 
will come back to the normal operation.

]

Ser group - Serial link parameter

[48] Add - Instrument address

Available: 

Always.

Range: 

oFF = 

Serial interface not used;

1 to 254.

[49] bAud - Baud rate 

Available: 

When [48] Add different from oFF.

Range: 

1200 =  1200 baud;
2400 =  2400 baud;

Summary of Contents for TC 10-L





















Reviews: