YOKOGAWA TB830D User Manual Download Page 8

Page: 8 / 85

<1. OVERVIEW>

1-1

IM 12E04B40-02EN

1st Edition : Mar. 08, 2023-00

1. OVERVIEW

Surface Scattering Light Turbidity Detector, composed of Turbidity Detector TB830D and Liquid

Analyzer FLXA402T, is a next-generation analyzer, developed based on years of experience,

combining the reliable measurement principle with our latest digital sensor technology realizing

high efficiency in facility operations. The product has successfully extended its life by employing

LED as the light source.

1.1

Measurement system and structure

TB830D is used with FLXA402T Liquid Analyzer for Turbidity and Chlorine. TB830D also can be

used with a sampling system to control the pressure or flow rate of samples.

TB830D Surface Scattering Light Turbidity Detector

TB830D measures turbidity. The Detection unit consists of the following three parts.

● Flow cell:

A sample flows through it. A light beam is emitted from the light source

onto the sample solution.

● Detection unit:

An optical system incorporating a Light source, Receiver, and lenses.

Desiccant equipped helps the dryness inside.

● Smart unit:

Memory of parameters, the control unit

FLXA402T Liquid Analyzer for Turbidity and Chlorine (converter)

Displays/Outputs measurement or status of connected detectors or controls detectors.
Refer to IM 12A01G01-03EN for the setup of the display, input/output, or communication.

Sampling System

The Head tank enables the pressure of a sample and the flow rate to stabilize. The Head tank

also reduces the effect of air bubbles.

For Automatic cleaning/Automatic zero calibration, a Relay box and/or solenoid valve is mounted.

TB830D

Surface Scattering

Light Turbidity Detector

Zero turbidity

filter

FLXA402T

Liquid Analyzer

for Turbidity and Chlorine

Head tank

Figure 1.1

Example “With sampling system” (-A3)

Summary of Contents for TB830D






















































































Search results

Summary of Contents for TB830D

Reviews:

YOKOGAWA TB830D, User Manual, Page: 8 / 85

Search results

Summary of Contents for TB830D

Reviews: