manualshive.com logo in svg

YOKOGAWA TB830D, User Manual, Page: 47 / 85

Share
Download
YOKOGAWA TB830D User Manual Download Page 47

 

 

<5.  FLXA402T sensor menu>

5-4

1st Edition : Mar. 08, 2023-00

IM 12E04B40-02EN

l

  Lightening IF

Shows a driving current value of the light source.

n

  Sensor wellness

l

  Light source diagnosis

The result shows how much the Light source condition has changed since the factory preset. The 

more 

n

 appears in each gauge, the more sound the Light source is. A gauge is indicated only 

when the setting of Sensor wellness for Light source is enabled. If the sensor wellness setting is 

“disabled, a bar (----) is displayed.

l

  Dried condition diagnosis 

Shows the dryness inside the detection unit. 

The more ■ appears, the more sound the dryness condition is.  If no ■is displayed, replace the 

desiccant. The gauge is displayed only when the setting of the dried condition is valid. When not, 

a bar (----) is displayed. 

l

  Replacement/Operating days 

Manages desiccant replacement day or operating days of Light source and wiper.
To reset each data, go to dialog of Sensor wellness reset. Press reset, then the number of 

operating days is reset to 0 but the replacement date is updated. See 5.4.

Only when the wellness setting is enabled, the result is displayed. 

n

  Predict. maintenance

l

  Last calibrated at

Displays a date when the last auto calibration took place and the last calibration menu was 

implemented.

l

  Next sequence start

When next auto wash, next auto calibration are scheduled, the next date on schedule is 

displayed.  

If you set a date/time for the first-time operation, the date and time for the first time operation is 

displayed. When you set Next auto calibration date to be updated automatically, the next date of 

auto calibration date is automatically updated.

n

  TB detector

Displays Serial number (Serial No.) of a connected Turbidity detection unit, software version 

(Software Rev.), Model code (Model code), internal serial number of CPT board, LED board and 

analog board (Internal SN.(CPT), Internal SN.(LED), Internal SN.(Analog) ).

n

  Converter log, Sensor log

Same display as on the converter “Detail”. 
See FLXA402T Operation of Converter IM 12A01G01-03EN 

Summary of Contents for TB830D






















































































Reviews:

No comments