manualshive.com logo in svg

YOKOGAWA TB830D, User Manual, Page: 67 / 85

Share
Download
YOKOGAWA TB830D User Manual Download Page 67

<8.  MAINTENANCE>

8-6

IM 12B01B30-02EN

1st Edition : Mar. 08, 2023-00

CAUTION

Do not mix up two different sizes (1 μm and 0.2 μm) of the zero turbidity filter element if you install 

two zero turbidity filters.

Air vent

O-ring

Filter element

Remove

Case

Figure 8.5 

Zero Turbidity Filter Element Replacement

Table 8.3 

Filter element

Part No.

Name

K9008ZD

1 μm filter element

K9726EH

0.2 μm filter element

K9411UD

O-ring

8.8 

LED Replacement

 CAUTION

•  Turn off the power of TB830D before replacing the LED.

•  LED may be damaged by static electricity. When replacing the LED be sure to take 

measures against static electricity, such as wearing a grounded wristband.

LED light source usually lasts more than 3 years. However, it is recommended to replace it every 

3 years for preventive maintenance.
This section explains how to replace the LED.
(1)  Stops supplying Power Supply to TB830D.
(2)  Remove the top cover of the detection unit by loosening the four (4) setscrews.
(3)  Loosen the four (4) setscrews on LED ASSY.
(4)  Remove the cable connector from LED ASSY (Figure 8.7).

(5)  Replace LED ASSY with a new one.

(6)  Attach the cable connector to the new LED ASSY (Figure 8.8).

Summary of Contents for TB830D






















































































Reviews:

No comments