manualshive.com logo in svg

YOKOGAWA TB830D, User Manual, Page: 18 / 85

Share
Download
YOKOGAWA TB830D User Manual Download Page 18

  

<2.  INSTALLATION, PIPING, AND WIRING>

2-5

IM 12B01B30-02EN

1st Edition : Mar. 08, 2023-00

(2)  Tap-water piping

 

This is a piping for supplying detector with cleaning water and zero water. Use tap water or 

other water with a turbidity of 2 NTU or less. The pressure of the water to be used is 100 to 

500 kPa . The pipe joints are rigid PVC pipes with a nominal diameter VP16 (O.D. ø22mm). 

Before piping, install any fittings that conform to the pipe diameter in the same way as the 

sample piping.

 

You should install a check valve before the tap water pipe to prevent backflow.

(3)  Drain piping

 

This piping is for discharging the sample and tap water supplied to detector into drains, or 

the like. The pipe joints are rigid PVC pipes with a nominal diameter of VP40.

 

Connect a rigid PVC pipe with a VP40 or higher capacity, and connect the pipe so that 

sediment does not accumulate or drain stagnations in the pipe.

Drain VP40

Tap water outlet

VP16 pipe

Sample inlet

VP16 pipe

Figure 2.4 

Pipe position (with sampling)

Summary of Contents for TB830D






















































































Reviews:

No comments