manualshive.com logo in svg

YOKOGAWA TB830D, User Manual, Page: 49 / 85

Share
Download
YOKOGAWA TB830D User Manual Download Page 49

 

 

<5.  FLXA402T sensor menu>

5-6

1st Edition : Mar. 08, 2023-00

IM 12E04B40-02EN

5.6 

Maintenance

Sensor menu >   Maintenance 

Figure 5.8 

When you have a password, the password verification appears. Upon successful confirmation, 

Maintenance screen appears.
For further information on the password setting, see FLXA402T Operation of Converter IM 

12A01G01-03EN 5.4 Password.

5.6.1 

Maintenance mode

Switches the mode between the measurement and the maintenance. For Maintenance mode, 

See “3. PREPARATION for OPERATION”.

5.6.2 

Light source On/Off

Switches On/Off Light source. This function is enabled only when Maintenance mode is On.

5.6.3 

SV/Wiper operation

SV/Wiper operation 

TB830D does not use wipers. The function controls the solenoid valve connected to Relay box. 

You can go to the same screen when tapping (MAN SW 

 of Main menu. This function is 

enabled only when Maintenance mode is On.

CAUTION

SV4 (pinch valve) is set to automatically turn off after 10 minutes of operation to prevent 

overheating due to energization.

Summary of Contents for TB830D






















































































Reviews:

No comments