manualshive.com logo in svg

YOKOGAWA ROTAMETER RAMC, User Manual, Page: 2 / 49

Share
Download
YOKOGAWA ROTAMETER RAMC User Manual Download Page 2

Contents

1.  Introduction .........................................................................................1-1

1.1 Target group ......................................................................................................1-1

1.2 Applicable documents .....................................................................................1-1

1.3 General items ....................................................................................................1-1

2.  About PROFIBUS PA ..........................................................................2-1

2.1  Outline ..............................................................................................................2-1

2.2  Internal Structure of RAMC PROFIBUS PA ..................................................2-1

2.3  Logical Device Structure ................................................................................2-1

3.  Installation ..........................................................................................3-1

3.1  Wiring System Configuration .........................................................................3-1

3.2  Connection of Devices ...................................................................................3-1

4.  Start of Operation ..............................................................................4-1

4.1  Integration of GSD ..........................................................................................4-1

4.2  Important Device Settings  ............................................................................4-1

4.3  Cyclic Data Exchange .....................................................................................4-2

4.4  Setting of Write Protection .............................................................................4-2

4.5  Using the Keys ................................................................................................4-2

4.6  Menu Structure ................................................................................................4-3

5.  Block Setting ......................................................................................5-1

5.1 Parameters and Initial Settings  .....................................................................5-1

5.2  Physical Block (PB) Parameters ....................................................................5-1

5.3  Analog Input (AI) Block Parameters .............................................................5-2

5.4  Transducer Block (TB) Parameters ...............................................................5-3

6.  Status and Diagnostic Information ..................................................6-1

6.1  Status description ...........................................................................................6-1

6.2  Diagnostics ......................................................................................................6-3

6.3  Status impacts of Alarm settings ..................................................................6-4

<1CONTENTS>

i

All Rights Reserved. Copyright © 2006, Rota Yokogawa 

IM 01R01B02-01E-E    5th edition October 01, 2020 -00

Summary of Contents for ROTAMETER RAMC


















































Reviews:

No comments