manualshive.com logo in svg

YOKOGAWA ROTAMETER RAMC, User Manual, Page: 8 / 49

Share
Download
YOKOGAWA ROTAMETER RAMC User Manual Download Page 8

4.  START OF OPERATION

4-1

All Rights Reserved. Copyright © 2006, Rota Yokogawa 

IM 01R01B02-01E-E    5th edition October 01, 2020 -00

4.1  Integration of GSD

PROFIBUS PA system requires GSD file which describes the device parameters such as the transmission 

rate supported, input, output data, data format and data length.             

The GSD files described below are available to RAMC. 
You can download the GSD file from 

http://www.profibus.com/products/gsd-files/

.

Table 4.1 GSD files

GSD file name

Ident. Number

Comment

PA139700.GSD (AIx1)

0x9700

Profile specific

RY014582.GSD

0x4582

Device specific

4.2  Important Device Settings 

The tables below show items (parameters) which need special care to ensures a proper working of the 

RAMC Profibus type. 

Table 4.1 General settings

Item

Settings

Bus address

Set to 0x7E (126) by default unless otherwise specified when ordered

In case of unit change (compared to initial ordering) it is recommended to change the OUT_SCALE parameter 

as described in table 4.3 only. Change of the Process Variable needs in addition the changes described in 
the tables 4.2 and 4.3.

Table 4.2 Initial settings of Transducer Block

Item

Settings for Volume flow

Settings for Mass flow

Parameter: VOLUME_FLOW_UNITS

Choose unit (initially set to unit specified 

when ordered)

Not active 1("Volume flow passivated")

Parameter: MASS_FLOW_UNITS

Not active 1 ("Mass flow passivated")

Choose unit (initially set to unit specified 

when ordered)

NOTE

   Change of the parameters VOLUME_FLOW_UNITS to MASS_FLOW_UNITS or vice versa needs in    
  addition the adaptation of the parameter CHANNEL inside the AI block, to make the change effective on    
   the OUT parameter.

Table 4.3 Initial settings of AI Function Block

Item

Settings for Volume flow

Settings for Mass flow

Parameter: PV_SCALE 
Sub-parameter: Array 1

Set upper range limit (set to scale upper range as specified when ordered)

Parameter: PV_SCALE 
Sub-parameter: Array 2

Set lower range limit (set to scale lower range as specified when ordered)

Parameter: OUT_SCALE

Sub-parameter: Units_Index

Choose unit (set to unit specified when ordered)

Parameter: OUT_SCALE
Sub-parameter: EU_at_100%

Set upper range limit (set to scale upper range as specified when ordered)

Parameter: OUT_SCALE
Sub-parameter: EU_at_0%

Set lower range limit (set to scale lower range as specified when ordered)

Parameter: CHANNEL

0x0111 (273)

0x0115 (277)

 

4.  Start of Operation

Summary of Contents for ROTAMETER RAMC


















































Reviews:

No comments