YOKOGAWA F3LR02-0N, User Manual

Page: 180 / 210

C6-6
IM 34M06H45-01E 7th Edition : Aug.30, 2019-00
Subunit B: A subunit that is further from the main unit than the location of a channel
error where receiving from the main unit is still available through the
transmission channel between the subunit and main unit
Subunit C: A subunit that is further from the main unit than the location of a channel
error where only sending to the main unit is available or neither sending
to nor receiving from the main unit is available through the transmission
channel between the subunit and main unit
Table C6.5 Operation of Output Module and FAIL Signal Contact by Combination for Each
Configuration Setups and Channel Error Locations
Station
DIP SW1 of
F3LR02
Project Settings of WideField3 / Configuration single CPU module setting Multi-CPU module setting
Input/Output
Setup
Error Handling Setup
FAIL Signal Contact Output
Status of the power supply
module
Operation
of Output
Module
FAIL Signal Contact Output
Status of the power supply
module
Operation
of Output
Module Output
Setup
Subunit
Communication
Error
I/O modules
Error
FAIL1 FAIL2 FAIL1 FAIL2
Main unit N/A
Reset
(OFF)
Stop Don't Care
Shorted Open Shutdown Shorted Open Shutdown
Don't Care Stop
Continue
operation
Continue
operation
Open Shorted
Continue
operation
Open Shorted
Continue
operation
Hold
Stop Don't Care
Shorted Open Hold Shorted Open Hold
Don't Care Stop
Continue
operation
Continue
operation
Open Shorted
Continue
operation
Open Shorted
Continue
operation
Subunit
(A), (B),
ON
(Shutdown)
Reset
(OFF)
Stop Don't Care
Shorted Open Shutdown Shorted Open Shutdown
Don't Care Stop
Continue
operation
Continue
operation
Shorted Open Shutdown
(*2)
Shorted Open
Continue
operation (*2)
Hold
Stop Don't Care
Shorted Open Hold Shorted Open Hold
Don't Care Stop
Continue
operation
Continue
operation
Shorted Open
Continue
operation
Shorted Open
Continue
operation
OFF
(Hold)
Reset
(OFF)
Stop Don't Care
Shorted Open Shutdown Shorted Open Shutdown
Don't Care Stop
Continue
operation
Continue
operation
Open Shorted
Continue
operation
Open Shorted
Continue
operation
Hold
Stop Don't Care
Shorted
(*1)
Open
(*1)
Hold Shorted
(*1)
Open
(*1)
Hold
Don't Care Stop
Continue
operation
Continue
operation
Open Shorted
Continue
operation
Open Shorted
Continue
operation
Subunit
(C)
ON
(Shutdown)
Reset
(OFF)
Stop Don't Care
Shorted Open Shutdown
(*2)
Shorted Open Hold
(*2)
Don't Care Stop
Continue
operation
Continue
operation
Shorted Open Shutdown
(*2)
Shorted Open Hold
(*2)
Hold
Stop Don't Care
Shorted Open Hold Shorted Open Hold
Don't Care Stop
Continue
operation
Continue
operation
Shorted Open Hold Shorted Open Hold
OFF
(Hold)
Reset
(OFF)
Stop Don't Care
Open Shorted Hold Open Shorted Hold
Don't Care Stop
Continue
operation
Continue
operation
Open Shorted Hold Open Shorted Hold
Hold
Stop Don't Care
Open
(*1)
Shorted
(*1)
Hold Open
(*1)
Shorted
(*1)
Hold
Don't Care Stop
Continue
operation
Continue
operation
Open Shorted Hold Open Shorted Hold
Note
- As shown on *1 in Table C6.5, FAIL con
tacts’ condition is different between the
substation A/B and C if the DIPSW1 of the F3LR02 is set OFF for Hold and [Output
When Stopped] setting of [DIO Setup] in P
roject is ‘Hold’.
- Unavailable to shutdown signal output nevertheless DIP switch1 sets
ON(shutdown) and Project Settings/Configuration are OFF(reset) in a multi-CPU
module setting (Refer to table B6.1 *2)
.