Yazoo/Kees 968999663 Operator'S Manual Download Page 7

Page: 7 / 84

English-

SYMBOLS AND DECALS

Symbols and Decals

These symbols are found on the machine and in the operator’s manual.
Study them carefully so that you know what they mean.

Used in this publication to notify the reader of a risk of

personal injury or death

, particularly if the reader

should neglect to follow instructions given in the manual.

Used in this publication to notify the reader of a risk of

material damage

, particularly if the reader should

neglect to follow instructions given in the manual. Used also when there is a potential for misuse or
misassembly.

WARNING!
Xxxxxxx xxxx xxxxxxxx xxx x
Xxxxx xxxxxx xx.
xx xxxxxxxx xxxxx xxx xx.

IMPORTANT INFORMATION
Xxxxxxx xxxx xxxxxxxx xxx xxx
xxxx xxxxxx xx.

Parking brake

Do not stand here

Battery acid is corrosive, explosive,
and flammable

CE conformity
marking. Only for
European market

Warning! Rotating
blades, keep away from
the discharge deck

Do not touch rotating
parts

Fuel

Choke

Slow

Fast

Neutral

Reverse

Warning!

Noise emissions to the surroundings
in accordance with the European
Union’s directive. The machine’s
emission is stated in the chapter

TECHNICAL DATA

and on the decals.

Only machines for European market

Use protective glasses

Use protective gloves

Summary of Contents for 968999663





















































































Search results

Summary of Contents for 968999663

Reviews:

Brands by name

Popular brands

Yazoo/Kees 968999663, Operator'S Manual

Search results

Summary of Contents for 968999663

Reviews:

Brands by name

Popular brands