Yazoo/Kees 968999663 Operator'S Manual Download Page 21

Page: 21 / 84

English-

CONTROLS

5. Blade switch

In order to engage the mower deck, pull the
knob out; the mower blades are disengaged
when the knob is depressed.

6. Ignition Switch

The ignition key is placed on the driver’s
panel and is used to start and stop the
engine.

7. Fuses

The fuses are located in a holder to the left of
the hydraulic tank. They are flat pin fuses of
the same type used in automobiles.

There are three fuses, as well as socket for
one spare fuse.

Fuse ratings and functions:

•

20 A, Primary fuse.

•

7.5 A, Mower deck coupling.

•

7.5 A, Accessory outlet

•

Socket for spare fuse.

8011-510

Blade Switch

8011-521

Ignition key and hour meter

IMPORTANT INFORMATION
Do not run the starter for more than five
seconds each time. If the engine does not
start, wait about 10 seconds before re-
trying.

8011-746

Fuses

Summary of Contents for 968999663





















































































Search results

Summary of Contents for 968999663

Reviews:

Brands by name

Popular brands

Yazoo/Kees 968999663, Operator'S Manual

Search results

Summary of Contents for 968999663

Reviews:

Brands by name

Popular brands