Yazoo/Kees 968999663 Operator'S Manual Download Page 46

Page: 46 / 84

English-

MAINTENANCE

Replacing the Fuel Filter

Replace the line-mounted fuel filter every
100 hours (once per season) or more often if
it becomes clogged.

Replace the filter as follows:

1. Move the hose clamps away from the

filter. Use flat-nosed pliers.

2. Pull the filter loose from the hose ends.
3. Push the new filter into the hose ends.

Position the filter with the “FLOW” arrow
pointing up toward the fuel pump. If
necessary, a soap solution can be
applied to the filter ends to ease
mounting.

4. Move the hose clamps back toward the

filter.

Checking the Fuel Pump’s Air Filter

Regularly check that the fuel pump’s air filter
is free from dirt.

On Kohler engine, removal of the pump
screws is not needed, due to the filter facing
outwards.

Remove the screws and open the pump, no
hoses need be removed.

The filter can be cleaned with a brush if
necessary.

Replace the filter on the console.

8009-146

Fuel filter Kawasaki

8011-468

Fuel filter Kohler

8009-147

The fuel pump’s air filter

Summary of Contents for 968999663





















































































Search results

Summary of Contents for 968999663

Reviews:

Brands by name

Popular brands

Yazoo/Kees 968999663, Operator'S Manual

Search results

Summary of Contents for 968999663

Reviews:

Brands by name

Popular brands