manualshive.com logo in svg

Yazoo/Kees 968999663, Operator'S Manual

Share
Download
Yazoo/Kees 968999663 Operator'S Manual Download Page 31

English-

29

OPERATION

To start an engine with a weak 

battery

If your battery is too weak to start the engine, 
it should be recharged. (See “Battery" in the 
“Maintenance" section). 

If “jumper cables” are used for emergency 
starting, follow this procedure:

To attach jumper cables

•

Connect each end of the RED cable to 
the POSITIVE (+) terminal on each 
battery, taking care not to short against 
chassis.

•

Connect one end of the BLACK cable to 
the NEGATIVE (-) terminal of the fully 
charged battery.

•

Connect the other end of the BLACK 
cable to a good CHASSIS GROUND on 
the mower with the discharged battery, 
away from the fuel tank and battery.

To remove cables, reverse order

•

Remove BLACK cable first from chassis 
and then from the fully charged battery.

•

Remove RED cable last from both 
batteries.

WARNING!
Lead-acid batteries generate 
explosive gases. Keep sparks, 
flame and smoking materials 
away from batteries. Always 
wear eye protection when 
around batteries.

8011-642

Jumper cables connection

IMPORTANT INFORMATION
Your mower is equipped with a 12-volt 
negative grounded system. The other 
vehicle must also be a 12-volt negative 
grounded system. Do not use your mower 
battery to start other vehicles.

Summary of Contents for 968999663





















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands