manualshive.com logo in svg

Yazoo/Kees 968999663, Operator'S Manual

Share
Download
Yazoo/Kees 968999663 Operator'S Manual Download Page 51

English-

49

MAINTENANCE

To adjust anti-scalp rollers

Anti-scalp rollers are properly adjusted when 
they are just slightly off of the ground when 
the deck is at the desired cutting height in the 
operating position. Anti-scalp rollers then 
keep the deck in the proper position to help 
prevent scalping in most terrain conditions.

The anti-scalp rollers can be set in three 
positions:

•

Upper position 1.5” to 3”/38 to 76 mm 
grass.

•

Middle position 3” to 4.5”/76 to 114 mm 
grass.

•

Lower position 4.5” to 6”/114 to 152 mm 
grass.

The rollers should be approximately 1/4”/6.5 
mm from ground. Do not adjust the rollers to 
support the deck.

Engine oil cooler

Kohler engine only.

1. Clean the outside of fins with a brush.
2. Remove the two screws holding the 

cooler unit to the blower housing.

3. Tilt the cooler downward.
4. Clean the inside of the cooler with a 

brush or with compressed air.

5. Reinstall the oil cooler to the blower 

housing.

CZ-9

Anti-scalp roller

IMPORTANT INFORMATION

Adjust Anti-scalp rollers with the 

mower on a flat level surface.

IMPORTANT INFORMATION
The anti-scalp rollers must not be used for 
gauge wheels or the roller and deck may 
be damaged.

8011-472

Engine oil cooler

Summary of Contents for 968999663





















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands