manualshive.com logo in svg

Yazoo/Kees 968999663, Operator'S Manual

Share
Download
Yazoo/Kees 968999663 Operator'S Manual Download Page 20

English-

18

CONTROLS

2. Hour Meter

The hour meter displays the total operating 
time.

It will flash CHG OIL (Change Oil) at 50 hour 
intervals. The flash duration is one hour 
before and one hour after the interval. The 
CHG OIL icon will come on and shut off 
automatically. The hour meter can not be 
manually reset.

3. Tracking knob

The tracking knob is located in front of the left 
control lever. Rotating this knob allows fine 
tuning adjustments so that the machine 
tracks straight with the drive levers in the full 
forward position.

Rotate the knob clockwise (as viewed from 
the operating position) to increase the speed 
or counter clockwise to decrease the speed 
on the left control lever. Example: If control 
levers are full forward and the unit turns to the 
right, turn the tracking knob counter 
clockwise to decrease the speed on the left 
control lever.

4. Parking Brake

The parking brake is found on the left of the 
machine. Pull the lever backward to activate 
the brake and forward to release it. 

hour meter

Hour meter

8011-442

Tracking knob

8011-511

Parking brake not activated

Summary of Contents for 968999663





















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands