11
12
MAINTENANCE INSTRUCTIONS
SHREDDING BLADES MAINTENANCE
To inspect or replace the double sided shredding blades
there is no need to remove the cutter base. To remove sim-
ply undo the counter sunk screws with the 6mm hex
wrench supplied with the machine and turn them through
180˚ These blades are double ground and can be used on
both sides. When blunt on both sides replace and insure
they are screwed in tightly.
ASSEMBLY
This is carried out in the reverse sequence to
that of disassembly but with careful inspection of all com-
ponents. Ensure that cutter base is assembled with the
scraping plates facing down towards the motor and that
the square washer is situated under the head of the cen-
ter hold down bolt. (Fig. 15)
Before replacing the top cover assembly ensure that the V-
cutter is positioned as shown in (Fig. 16) Replace the top
cover assembly and secure tightly the caging knobs. If
caging Knobs are not tight the motor will not start due to the
motor lock out switch not being activated.
CLEANING
After use, always wipe clean the outside of the shredder to
remove any build up of material with a damp cloth. Clean
the inside of the cutting chamber and remove any left over
material, Do not hose down with water.
Fig. 15
Fig. 16
Before removing Top
Hopper knob, insure
the machine is switched off, the red safety
switch and extension lead is removed and wait
until the machine comes to a complete stop.
WARNING:
PARTS LIST
39
39
45
45
44
44
13
13
51
51
57
57
56
56
66
66
67
67
68
68
40
40
16
16
16
16
16
16
18
18
10
10
15
15
18
18
52
52
46
46
47
47
48
48
53
53
61
61
64
64
70
70
71
71
25
25
22
22
20
20
18
18
19
19
21
21
12
12
11
11
14
14
62
62
24
24
5
5
69
69
65
65
60
60
59
59
58
58
50
50
43
43
41
41
35
35
37
37
17
17
9
9
4
4
6
6
7
7
7
7
7
7
13
13
54
54
63
63
23
23
26
26
55
55
49
49
42
42
36
36
38
38
34
34
18
18
8
8
5
5
3
3
3
3
2
2
2
2
1
1
41
41
13
13
5
5
27
27
28
28
29
29
30
30
31
31
32
32
33
33
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
Parts No.
6266-200103
6200-200101
6134-200101
6024-200101
6WSB-08
6014-200101
6STBBM05-15
6270-200111
6263-200102
6158-200101
6134-200102
6SDABB04-20
6WFZ-08
6CE-06
6SDAZ-04-10
6WFZ-04
6263-200101
6NAZ-04
6WSB-04
6262-200106
6SDAZ-05-55
6059-200101
6NAZ-05
6SXDZ-10-35
Description
TOP HOPPER
SCREW
KNOB
RESTRAINNIG SPRING
SPRING WASHER
WASHER
SCREW
BODY
DUST PLATE
CUTTER CLAMP
KNOB
SCREW
WASHER
E RING
SCREW
WASHER
DUST PLATE
NUT
SPRING WASHER
RESTRAINING COVER
SCREW
BRACKET TUBE
NUT
SCREW
No.
37
38
39
40
41
42
43
44
45
46
47
48
25
26
27
28
29
30
31
32
33
34
35
36
Parts No.
6207-200102
6036-200101
6262-200101
6022-200001
6SDAZ-04-08
6262-200001
6010-200004
6010-200005
6099-200103
6SDABB04-14
6043-840001
6WFZ-06
6WSB-10
6158-200002
6156-200001
6250-200003
6267-200001
6200-200002
6250-200001
6268-200101
6124-200101
6200-200001
6WDB-08
6200-200102
Description
BRACKET CLAMP
SWITCH HOLDER
SWITCH COVER
CUT-OUT SWITCH
SCREW
SWITCH COVER
INTERNAL WIRE I
INTERNAL WIRE II
MOTOR ASS'Y
SCREW
CORD CLAMP
WASHER
SPRING WASHER
CUTTER CLAMP
SQUARE BUSH
V-CUTTER
V-CUTTER BASE
SCREW M10x10
CUTTER (BLADE)
CUTTER BASE
CUTTER BUSH
SCREW M8x18
SPRING WASHER
SCREW
No.
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
Parts No.
6SDAZ-06-12
6086-200104
6010-200006
6272-200002
6022-200002
6199-200002
6100-200101
6011-200005
6111-200101
6NAZ-08
6027-200101
6111-200102
6004-200104
6087-200102
6SRCB-08-16
6004-200103
6SRCB-08-40
6228-200013
6WFZ-12
6PB-26
6067-200007
6SJABB03-10
Description
SCREW
MOTOR COVER
INTERNAL WIRE
THERMOSTAT
ON/OFF SWITCH
CORD GUARD
PLATE
POWER CORD
STRENGTEN SHAFT
NUT
FRAME GASKET
WHEEL SHAFT
LEFT HOLDER
CONNECTING TUBE
SCREW
RIGHT HOLDER
SCREW
WHEEL
WASHER
PIN
WHEEL COVER
SCREW
71
6042-200001
WRENCH
72
6188-200402
MARTERIAL PUSH STICK
73
6280-200001
STARP BAG HOLD