manualshive.com logo in svg

Yamato WG 1000, Instruction Manual

Share
Download
Yamato WG 1000 Instruction Manual Download Page 48

 

 

45

 

In the Event of Failure… 

Remedy for Trouble 

 

Countermeasure against water leakage error 

1.  Turn off the earth leakage breaker at left surface of the main unit. 
2.  After repairing the defective area, wipe water off at the bottom in the unit, and dry thoroughly for 

re-starting the operation. 

3.  If the electrode is removed, make sure to reinstall it. 
4.  Close the door. 
5.  Turn on the earth breaker, and press POWER key. Now the defect is repaired, and the unit starts 

normal operation. 

 

<How to remove the lower front panel of WG250> 

1.  Remove the screws at left/right positions of the lower front panel. 
2.  Pull the panel frontward. Be careful of the cable of the drain switch specially used for water sampling 

table. 

3. Disconnect the cable of the drain switch for water sampling table. Then, remove the lower front panel. 

For installation, perform the above steps in reverse order (from 3 to 1). 

   

 

 

                                                         

 

Water leakage detection electrode 

WG1000

 

WG250

 

Summary of Contents for WG 1000

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands