Yamaha XVS65A Owner'S Manual Download

Page: 54 / 98

PERIODIC MAINTENANCE AND ADJUSTMENT

7-16

4. Insert the air filter element into the

air filter case as shown.

NOTICE:

Make sure that the air filter ele-
ment is properly seated in the
air filter case. The engine
should never be operated with-
out the air filter element in-
stalled, otherwise the piston(s)
and/or cylinder(s) may become
excessively worn.

[ECA10481]

5. Install the air filter case cover by

aligning the match marks and in-
stalling the bolts.

TIP

If dust or water collects in the air filter
check hose, remove the clamp from it,
and then remove the plug to drain the
hose.

1. Air filter element

1. Air filter element holder
2. Projection

3. Slot

1. Match marks

1. Air filter check hose

U1BF11E0.book Page 16 Tuesday, April 13, 2010 9:28 AM

Summary of Contents for XVS65A



































































































Search results

Summary of Contents for XVS65A

Reviews:

Related manuals for XVS65A

Brands by name

Popular brands

Yamaha XVS65A, Owner'S Manual

Search results

Summary of Contents for XVS65A

Reviews:

Related manuals for XVS65A

Brands by name

Popular brands