Yamaha XVS65A Owner'S Manual Download

Page: 34 / 98

FOR YOUR SAFETY – PRE-OPERATION CHECKS

5-2

Clutch

• Check operation.
• Lubricate cable if necessary.
• Check lever free play.
• Adjust if necessary.

Throttle grip

• Make sure that operation is smooth.
• Check cable free play.
• If necessary, have Yamaha dealer adjust cable free play and lubricate cable and

grip housing.

7-17, 7-25

Control cables

• Make sure that operation is smooth.
• Lubricate if necessary.

7-25

Wheels and tires

• Check for damage.
• Check tire condition and tread depth.
• Check air pressure.
• Correct if necessary.

7-18, 7-20

Brake and shift pedals

• Make sure that operation is smooth.
• Lubricate pedal pivoting points if necessary.

7-26

Brake and clutch levers

• Make sure that operation is smooth.
• Lubricate lever pivoting points if necessary.

7-26

Sidestand

• Make sure that operation is smooth.
• Lubricate pivot if necessary.

7-27

Chassis fasteners

• Make sure that all nuts, bolts and screws are properly tightened.
• Tighten if necessary.

—

Instruments, lights, signals
and switches

• Check operation.
• Correct if necessary.

—

Sidestand switch

• Check operation of ignition circuit cut-off system.
• If system is not working correctly, have Yamaha dealer check vehicle.

4-13

ITEM

CHECKS

PAGE

U1BF11E0.book Page 2 Tuesday, April 13, 2010 9:28 AM

Summary of Contents for XVS65A



































































































Search results

Summary of Contents for XVS65A

Reviews:

Related manuals for XVS65A

Brands by name

Popular brands

Yamaha XVS65A, Owner'S Manual

Search results

Summary of Contents for XVS65A

Reviews:

Related manuals for XVS65A

Brands by name

Popular brands