Yamaha XVS65A Owner'S Manual Download

Page: 68 / 98

PERIODIC MAINTENANCE AND ADJUSTMENT

7-30

nect the negative lead before
disconnecting the positive lead.

[ECA16302]

2. If the battery will be stored for more

than two months, check it at least
once a month and fully charge it if
necessary.

3. Fully charge the battery before in-

stallation.

NOTICE:

When install-

ing the battery, be sure the key
is turned to “OFF”, then con-
nect the positive lead before
connecting the negative lead.

[ECA16840]

4. After installation, make sure that

the battery leads are properly con-
nected to the battery terminals.

NOTICE

ECA16530

Always keep the battery charged.
Storing a discharged battery can
cause permanent battery damage.

EAU23526

Replacing the fuses

The main fuse and the fuse box, which
contains the fuses for the individual cir-
cuits, are located behind panel B. (See
page 7-9.)
If a fuse is blown, replace it as follows.

1. Turn the key to “OFF” and turn off

the electrical circuit in question.

2. Remove the blown fuse, and then

install a new fuse of the specified
amperage.

WARNING! Do not

use a fuse of a higher amperage
rating than recommended to

avoid causing extensive dam-
age to the electrical system and
possibly a fire.

[EWA15131]

1. Fuse box

2. Main fuse

3. Spare main fuse

1. Headlight fuse
2. Signaling system fuse

3. Ignition fuse

4. Carburetor heater fuse
5. Ignitor unit fuse

6. Spare fuse

U1BF11E0.book Page 30 Tuesday, April 13, 2010 9:28 AM

Summary of Contents for XVS65A



































































































Search results

Summary of Contents for XVS65A

Reviews:

Related manuals for XVS65A

Brands by name

Popular brands

Yamaha XVS65A, Owner'S Manual

Search results

Summary of Contents for XVS65A

Reviews:

Related manuals for XVS65A

Brands by name

Popular brands