Yamaha XVS65A Owner'S Manual Download

Page: 25 / 98

INSTRUMENT AND CONTROL FUNCTIONS

4-8

EAU13445

Catalytic converters

This vehicle is equipped with catalytic
converters in the exhaust system.

WARNING

EWA10862

The exhaust system is hot after op-
eration. To prevent a fire hazard or
burns:

●

Do not park the vehicle near
possible fire hazards such as
grass or other materials that
easily burn.

●

Park the vehicle in a place
where pedestrians or children
are not likely to touch the hot
exhaust system.

●

Make sure that the exhaust sys-
tem has cooled down before do-
ing any maintenance work.

●

Do not allow the engine to idle
more than a few minutes. Long
idling can cause a build-up of
heat.

NOTICE

ECA10701

Use only unleaded gasoline. The use
of leaded gasoline will cause unre-
pairable damage to the catalytic
converter.

EAU13550

Fuel cock

The fuel cock supplies fuel from the
tank to the carburetors while also filter-
ing it.
The fuel cock lever positions are ex-
plained as follows and shown in the il-
lustrations.

OFF

With the fuel cock lever in this position,
fuel will not flow. Always turn the fuel
cock lever to this position when the en-
gine is not running.

1. Arrow mark positioned over “OFF”

U1BF11E0.book Page 8 Tuesday, April 13, 2010 9:28 AM

Summary of Contents for XVS65A



































































































Search results

Summary of Contents for XVS65A

Reviews:

Related manuals for XVS65A

Brands by name

Popular brands

Yamaha XVS65A, Owner'S Manual

Search results

Summary of Contents for XVS65A

Reviews:

Related manuals for XVS65A

Brands by name

Popular brands